STM32W108C8 STMicroelectronics, STM32W108C8 Datasheet - Page 14

• Manufacturer Part Number: STM32W108C8
• Description: High-performance, IEEE 802.15.4 wireless system-on-chip with 64-Kybte Flash memory
• Manufacturer: STMicroelectronics

Specifications of STM32W108C8

• Receive Current (w/ Cpu): 27 mA
• Transmit Current (w/ Cpu, +3 Dbm Tx): 31 mA
• Low Deep Sleep Current, With Retained Ram And Gpio: 400 nA/800 nA with/without sleep timer
• Standard Arm Debug Capabilities: Flash patch and breakpoint; data watchpoint and trace; instrumentation trace macrocell
• Single Voltage Operation: 2.1-3.6 V with internal 1.8 V and 1.25 V regulators

Description
Note:
1.2.2
13/215
can be disabled for the lowest power mode. In the lowest power mode, only external events
on GPIO pins will wake up the chip. The STM32W108C8 has a fast startup time (typically
100 µs) from deep sleep to the execution of the first ARM® Cortex-M3 instruction.
The STM32W108C8 contains three power domains. The always-on high voltage supply
powers the GPIO pads and critical chip functions. Regulated low voltage supplies power the
rest of the chip. The low voltage supplies are be disabled during deep sleep to reduce power
consumption. Integrated voltage regulators generate regulated 1.25 V and 1.8 V voltages
from an unregulated supply voltage. The 1.8 V regulator output is decoupled and routed
externally to supply analog blocks, RAM, and Flash memories. The 1.25 V regulator output
is decoupled externally and supplies the core logic.
The digital section of the receiver uses a coherent demodulator to generate symbols for the
hardware-based MAC. The digital receiver also contains the analog radio calibration
routines and controls the gain within the receiver path.
In addition to 2 general-purpose timers, the STM32W108C8 also contains a watchdog timer
to ensure protection against software crashes and CPU lockup, a 32-bit sleep timer
dedicated to system timing and waking from sleep at specific times and an ARM® standard
system event timer in the NVIC.
The STM32W108C8 integrates hardware support for a Packet Trace module, which allows
robust packet-based debug.
The STM32W108C8 is not pin-compatible with the previous generation chip, the SN250,
except for the RF section of the chip. Pins 1-11 and 45-48 are compatible, to ease migration
to the STM32W108C8.
ARM® Cortex™-M3 core
The STM32W108C8 integrates the ARM® Cortex™-M3 microprocessor, revision r1p1,
developed by ARM Ltd, making the STM32W108C8 a true system-on-a-chip solution. The
ARM® Cortex-M3 is an advanced 32-bit modified Harvard architecture processor that has
separate internal program and data buses, but presents a unified program and data address
space to software. The word width is 32 bits for both the program and data sides. The
ARM® Cortex-M3 allows unaligned word and half-word data accesses to support efficiently-
packed data structures.
The ARM® Cortex-M3 clock speed is configurable to 6 MHz, 12 MHz, or 24 MHz. For
normal operation 12 MHz is preferred over 24 MHz due to its lower power consumption. The
6 MHz operation can only be used when radio operations are not required since the radio
requires an accurate 12 MHz clock.
The ARM® Cortex-M3 in the STM32W108C8 has also been enhanced to support two
separate memory protection levels. Basic protection is available without using the MPU, but
the usual operation uses the MPU. The MPU protects unimplemented areas of the memory
map to prevent common software bugs from interfering with software operation. The
architecture could also separate the networking stack from the application code using a fine
granularity RAM protection module. Errant writes are captured and details are reported to
the developer to assist in tracking down and fixing issues.
Doc ID 018587 Rev 2
STM32W108C8