STM32F407IG STMicroelectronics, STM32F407IG Datasheet - Page 65
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
STM32F407IG
Manufacturer Part Number
STM32F407IG
Description
High-performance and DSP with FPU, ARM Cortex-M4 MCU with 1 Mbyte Flash, 168 MHz CPU, Art Accelerator, Ethernet
Manufacturer
STMicroelectronics
Datasheet
1.STM32F405VG.pdf
(167 pages)
Specifications of STM32F407IG
Core
ARM 32-bit Cortex™-M4 CPU with FPU, Adaptive real-time accelerator (ART Accelerator™) allowing 0-wait state execution from Flash memory, frequency up to 168 MHz, memory protection unit, 210 DMIPS/1.25 DMIPS/MHz (Dhrystone 2.1), and DSP instructions
3×12-bit, 2.4 Msps A/d Converters
up to 24 channels and 7.2 MSPS in triple interleaved mode
General-purpose Dma
16-stream DMA controller with FIFOs and burst support
Up To 17 Timers
up to twelve 16-bit and two 32-bit timers up to 168 MHz, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input
10/100 Ethernet Mac With Dedicated Dma
supports IEEE 1588v2 hardware, MII/RMII
Rtc
subsecond accuracy, hardware calendar
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STM32F407IGH6
Manufacturer:
STMicroelectronics
Quantity:
1
Company:
Part Number:
STM32F407IGH6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
STM32F407IGH6
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
STM32F407IGT6
Manufacturer:
ST
Quantity:
10 000
Company:
Part Number:
STM32F407IGT6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
STM32F407IGT6
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
STM32F407IGT6.
Manufacturer:
EXAR
Quantity:
15 225
STM32F405xx, STM32F407xx
5.3
5.3.1
Table 11.
V
Symbol
DDA
f
f
f
PCLK1
PCLK2
V
HCLK
V
BAT
DD
(3)(4)
Table 9.
1. All main power (V
2. Negative injection disturbs the analog performance of the device. See note in
3. Positive injection is not possible on these I/Os. A negative injection is induced by V
4. A positive injection is induced by V
5. When several inputs are submitted to a current injection, the maximum
Table 10.
Operating conditions
General operating conditions
General operating conditions
Internal AHB clock frequency
Internal APB1 clock frequency
Internal APB2 clock frequency
Standard operating voltage
Analog operating voltage
(ADC limited to 1.2 M samples)
Analog operating voltage
(ADC limited to 1.4 M samples)
Backup operating voltage
ΣI
supply, in the permitted range.
characteristics.
never be exceeded. Refer to
never be exceeded. Refer to
positive and negative injected currents (instantaneous values).
I
INJ(PIN)
Symbol
INJ(PIN)
Symbol
I
I
VDD
VSS
I
T
IO
STG
T
J
(2)
(4)
Parameter
Current characteristics
Thermal characteristics
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Injected current on five-volt tolerant I/O
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
DD
, V
Storage temperature range
Maximum junction temperature
DDA
) and ground (V
Table 8
Table 8
Doc ID 022152 Rev 2
IN
>V
for the values of the maximum allowed input voltage.
for the values of the maximum allowed input voltage.
DD
DD
Must be the same potential as V
SS
VOS bit in PWR_CR register = 0
power lines (source)
Ratings
SS
while a negative injection is induced by V
VOS bit in PWR_CR register= 1
ground lines (sink)
, V
Ratings
SSA
) pins must always be connected to the external power
(4)
Conditions
(3)
(1)
(1)
Σ
I
INJ(PIN)
DD
(5)
Electrical characteristics
Section 5.3.20: 12-bit ADC
(1)
(5)
–65 to +150
is the absolute sum of the
IN
Value
IN
125
1.8
1.8
<V
1.65
Min
2.4
<V
0
0
0
0
SS
(2)
(2)
SS
–5/+0
. I
Max.
±25
150
150
. I
25
25
±5
INJ(PIN)
INJ(PIN)
Max
144
168
3.6
3.6
3.6
3.6
42
84
must
must
Unit
Unit
65/167
°C
°C
mA
MHz
Unit
V
V
V