STM32F103T8 STMicroelectronics, STM32F103T8 Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
STM32F103T8
Manufacturer Part Number
STM32F103T8
Description
Mainstream Performance line, ARM Cortex-M3 MCU with 64 Kbytes Flash, 72 MHz CPU, motor control, USB and CAN
Manufacturer
STMicroelectronics
Datasheet
1.STM32F103T8.pdf
(99 pages)
Specifications of STM32F103T8
Conversion Range
0 to 3.6 V
Peripherals Supported
timers, ADC, SPIs, I2Cs and USARTs
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STM32F103T8U6
Manufacturer:
ST
Quantity:
13 000
Company:
Part Number:
STM32F103T8U6
Manufacturer:
STMicroelectronics
Quantity:
20 000
Company:
Part Number:
STM32F103T8U6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
STM32F103T8U6
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
STM32F103T8U6TR
Manufacturer:
STMicroelectronics
Quantity:
10 000
Company:
Part Number:
STM32F103T8U7
Manufacturer:
ST
Quantity:
100
Description
2.3.11
2.3.12
Note:
16/99
in reset mode when V
external reset circuit.
The device features an embedded programmable voltage detector (PVD) that monitors the
V
generated when V
than the V
message and/or put the MCU into a safe state. The PVD is enabled by software.
Refer to
V
Voltage regulator
The regulator has three operation modes: main (MR), low power (LPR) and power down.
●
●
●
This regulator is always enabled after reset. It is disabled in Standby mode, providing high
impedance output.
Low-power modes
The STM32F103xx performance line supports three low-power modes to achieve the best
compromise between low power consumption, short startup time and available wakeup
sources:
●
●
●
The RTC, the IWDG, and the corresponding clock sources are not stopped by entering Stop
or Standby mode.
DD
POR/PDR
/V
MR is used in the nominal regulation mode (Run)
LPR is used in the Stop mode
Power down is used in Standby mode: the regulator output is in high impedance: the
kernel circuitry is powered down, inducing zero consumption (but the contents of the
registers and SRAM are lost)
Sleep mode
In Sleep mode, only the CPU is stopped. All peripherals continue to operate and can
wake up the CPU when an interrupt/event occurs.
Stop mode
The Stop mode achieves the lowest power consumption while retaining the content of
SRAM and registers. All clocks in the 1.8 V domain are stopped, the PLL, the HSI RC
and the HSE crystal oscillators are disabled. The voltage regulator can also be put
either in normal or in low power mode.
The device can be woken up from Stop mode by any of the EXTI line. The EXTI line
source can be one of the 16 external lines, the PVD output, the RTC alarm or the USB
wakeup.
Standby mode
The Standby mode is used to achieve the lowest power consumption. The internal
voltage regulator is switched off so that the entire 1.8 V domain is powered off. The
PLL, the HSI RC and the HSE crystal oscillators are also switched off. After entering
Standby mode, SRAM and register contents are lost except for registers in the Backup
domain and Standby circuitry.
The device exits Standby mode when an external reset (NRST pin), an IWDG reset, a
rising edge on the WKUP pin, or an RTC alarm occurs.
DDA
Table 11: Embedded reset and power control block characteristics
PVD
and V
power supply and compares it to the V
threshold. The interrupt service routine can then generate a warning
PVD
DD
.
/V
DD
DDA
is below a specified threshold, V
drops below the V
Doc ID 13587 Rev 13
PVD
PVD
threshold and/or when V
threshold. An interrupt can be
POR/PDR
STM32F103x8, STM32F103xB
, without the need for an
DD
for the values of
/V
DDA
is higher