1-1600636-5 TE Connectivity, 1-1600636-5 Datasheet - Page 7
![](/photos/41/86/418698/pr177309618a_sml.jpg)
1-1600636-5
Manufacturer Part Number
1-1600636-5
Description
Manufacturer
TE Connectivity
Specifications of 1-1600636-5
Product Series
XL
Connector Type
Connector Assembly
Termination Style
Panel
Mating Type
Blindmate
Guides
With
Mating Functionality
Mate First-Break Last
Voltage Rating (signal) (vac)
60
Voltage Rating (power) (vdc)
200
Sequencing
Yes
Connector Configuration Orientation
Right-to-Left
Centerline, Dc Module (mm [in])
6.35 [0.250]
Centerline, Matrix (mm [in])
2.54 x 2.54 [.100 x .100]
Contact Type
Socket
Connector Style
Receptacle
Housing Material
Thermoplastic - GF
Total Number Of Dc Power
8
Total Number Of Signal
24
Connector Contact Configuration (no. Of Pos./type)
4/DC Power, 24/Signal, 4/DC Power
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Not relevant for lead free process
Rohs/elv Compliance History
Always was RoHS compliant
Application Use
Cable-to-Board
4.
4.1.
4.2.
4.3.
4.4.
Rev C
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form, fit or function are made to the product or manufacturing
process, product assurance shall coordinate requalification testing, consisting of all or part of the
original testing sequence as determined by development/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product meets the requirements of Figure 3. Failures
attributed to equipment, test setup or operator deficiencies shall not disqualify the product. If product
failure occurs, corrective action shall be taken and specimens resubmitted for qualification. Testing to
confirm corrective action is required before resubmittal.
Quality Conformance Inspection
The applicable quality inspection plan shall specify the sampling acceptable quality level to be used.
Dimensional and functional requirements shall be in accordance with the applicable product drawing
and this specification.
Specimen Selection
Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be
selected at random from current production. Test group 1 shall consist of 6 mated pairs (panel
mount receptacle to right angle header, with 8 and 14 AWG wires). Test group 2 shall consist of
12 mated pairs (panel mount to right angle header and squeeze-to-release to Vertical header,
with sampling of all single crimp wire configurations). Test group 3 shall consist of 10 mated pairs
(panel mount to right angle header and straight to vertical header, with 8 and 10 AWG wires).
Test group 4 shall consist of 10 mated pairs (panel mount to right angle header and straight to
vertical header, with 8 and 10 AWG wires). Test group 5 shall consist of a minimum of 11 mated
pairs (panel mount to right angle header), 3 specimens with 10 AWG wires, 3 specimens with 14
AWG wires, and 5 specimens with 8 AWG wires. Test group 6 shall consist of 12 contacts per
specified wire crimp combination. All contact insertion/retention tests shall consist of 15 contacts,
secondary locks, and housing circuits. Test group 7 shall consist of 32 power contacts with 10
AWG wires and 24 signal contacts with 22 AWG wires installed in various locations in the cable
connector housings for the contact retention angled pull test. Specimens for the housing lock
strength angled pull test shall consist of 12 mated pairs using power contacts with 8 AWG wire for
the ACP positions and 10 AWG wire for the standard power positions.
Test collaterals are as follows:
Test Sequence
Qualification inspection shall be verified by testing specimens as specified in Figure 4.
1.
2.
3.
Temperature rise printed circuit boards 60-474407 and 60-474408.
Low level contact resistance and mechanical board 60-474409.
Vibration fixture top plate 39-474410, bottom plate 39-474411, and vibration panel 39-
474412.
108-2157
7 of 9