1-1600636-5 TE Connectivity, 1-1600636-5 Datasheet
1-1600636-5
Specifications of 1-1600636-5
Related parts for 1-1600636-5
1-1600636-5 Summary of contents
Page 1
... Qualification Test Report number for this testing is 501-597. This documentation is on file at and available from Engineering Practices and Standards (EPS). | Additional testing on part number 1874902-1 using 12 AWG wire on 3 adjacent contacts and .300 pitch | at 28 amperes was performed by TUV. The project number for this testing is S1600403-101. ...
Page 2
... Adjacent Adjacent Adjacent Adjacent contacts Contacts Contacts Contacts --- 35 ----- ----- 28 --- --- --- --- --- Procedure EIA-364-18. Visual and dimensional ( inspection per product drawing. EIA-364-18. Visual inspection. EIA-364-23. Subject specimens to 100 milliamperes maximum and 20 millivolts maximum open circuit voltage ...
Page 3
... DC 500 megohms minimum for signal contacts. 1000 megohms minimum for power contacts. 1 minute hold with no breakdown or flashover maximum temperature rise at / specified current. MECHANICAL No discontinuities of 1 microsecond or longer duration. See Note. No discontinuities of 1 microsecond or longer duration. ...
Page 4
... Procedure EIA-364-13. Measure force necessary to unmate specimens at a maximum rate of 1 inch per minute. Size signal contacts 3 times using gage 1, then insert gage 2 and measure force necessary to separate. See Figure 5. EIA-364-5. Measure force necessary to insert contact into housing. EIA-364-29. Apply axial load to wire, as crimped to contacts ...
Page 5
... Clamp contacts as shown in Figure 6. EIA-364-32. Subject specimens to 36 cycles between -20 and 105 EIA-364-31, Method III, Condition B without cold shocks. Subject specimens to 10 cycles (10 days) between 25 and 95% RH. EIA-364-17, Method A, Test Condition 4. Subject mated specimens to 105 / for 504 hours (21 days). ...
Page 6
... Temperature life Mixed flowing gas Final examination of product (a) See paragraph 4.1.A. NOTE (b) Numbers indicate sequence in which tests are performed. (c) Energize at current for 18 (d) Precondition specimens with 5 durability cycles. (e) Power only in housing, signal with gage. (f) Precondition specimens with 50 durability cycles Rev C Test Group (a) ...
Page 7
... AWG wires). Test group 4 shall consist of 10 mated pairs (panel mount to right angle header and straight to vertical header, with 8 and 10 AWG wires). Test group 5 shall consist of a minimum of 11 mated pairs (panel mount to right angle header), 3 specimens with 10 AWG wires, 3 specimens with 14 AWG wires, and 5 specimens with 8 AWG wires ...
Page 8
... Tolerance: Unless otherwise specified, ±.005 or ± 2 degrees as applicable. NOTE 2. Material: AISI Type 02 tool steel per Material Specification 100-15. 3. Heat Treat: Rockwell C50-55 4. Gage surface shall be clean of contaminates or lubricants. Rev C Gage “A” Number Dimension 1 .0260 +.0000/-.0001 2 .0240 +.0001/-.0000 ...
Page 9
... Tolerance: Unless otherwise specified, ±.005 or ± 2 degrees as applicable. NOTE 2. Material: AISI Type 02 tool steel per Material Specification 100-15. 3. Heat Treat: Rockwell C50-55. Rev C Figure 6 Power Contact Tensile Test Clamp 108-2157 ...