MCP6548-E/MS Microchip Technology, MCP6548-E/MS Datasheet
MCP6548-E/MS
Specifications of MCP6548-E/MS
Available stocks
Related parts for MCP6548-E/MS
MCP6548-E/MS Summary of contents
Page 1
... Propagation Delay: 4 µs (typ., 100 mV Overdrive) • Wide Supply Voltage Range: 1.6V to 5.5V • Single available in SOT-23-5, SC-70-5 * packages • Available in Single, Dual and Quad • Chip Select (CS) with MCP6548 • Low Switching Current • Internal Hysteresis: 3.3 mV (typ.) • Temperature Range: - Industrial: -40° ...
Page 2
... Limit the output current to Absolute Maximum Rating of 30 mA. The minimum SS = 25° /2, V – Conditions ≥ OUT -0. 2. -0. (Note -40°C to +125° (Note -40°C to +125° (Note -40°C to +125° (Note +85° (Note +125° (Note -25° 25° © 2006 Microchip Technology Inc. ...
Page 3
... MAX f MAX Input Noise Voltage E Note 1: t and t depend on the load (R R PLH 2: Propagation Delay Skew is defined as: t MCP6548 CHIP SELECT (CS) CHARACTERISTICS Electrical Specifications: Unless otherwise indicated 2.74 kΩ and (Refer to Figures 1-1 and 1-3 Parameters Sym CS Low Specifications CS Logic Threshold, Low ...
Page 4
... (typ (typ.) CS FIGURE 1-1: Timing Diagram for the CS pin on the MCP6548. TEMPERATURE CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, V Parameters Temperature Ranges Specified Temperature Range Operating Temperature Range Storage Temperature Range Thermal Package Resistances Thermal Resistance, 5L-SC-70 ...
Page 5
... V 5 OUT – Time (1 ms/div) FIGURE 2-3: The MCP6546/6R/6U/7/8/9 comparators show no phase reversal. © 2006 Microchip Technology Inc. MCP6546/6R/6U/7/8/9 = +1.6V to +5.5V GND +25° 18% 1200 Samples 16 14% 12% 10 1.6 2.0 2.4 2.8 3.2 3.6 4.0 4.4 4.8 5.2 5.6 6.0 FIGURE 2- ...
Page 6
... Ambient Temperature (°C) Input Hysteresis Voltage vs +125° +85° +25° -40° +125° Common Mode Input Voltage (V) Input Hysteresis Voltage vs. = 1.6V 5. +125° +85° +25° -40°C A Common Mode Input Voltage (V) Input Hysteresis Voltage vs. = 5.5V. DD © 2006 Microchip Technology Inc. ...
Page 7
... IN DD 0.1 Sweep V – 0.0 0.0 0.2 0.4 0.6 0.8 1.0 Common Mode Input Voltage (V) FIGURE 2-15: Quiescent Current vs. Common Mode Input Voltage © 2006 Microchip Technology Inc. MCP6546/6R/6U/7/8/9 = +1.6V to +5.5V GND 10000 10n 1000 1n 100p 100 10p 100f 0.1 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 ...
Page 8
... Pull-up to Supply Voltage Difference, V – Supply Current vs. Pull- -40° +25° +85° +125°C A Power Supply Voltage (V) Output Short Circuit Current – +125° +85° +25° -40° Output Current (mA) Output Voltage Headroom = 5.5V. DD © 2006 Microchip Technology Inc. ...
Page 9
... PHL Overdrive 100 mV Overdrive PLH 0 1.5 2.0 2.5 3.0 3.5 4.0 Power Supply Voltage (V) FIGURE 2-27: Propagation Delay vs. Power Supply Voltage. © 2006 Microchip Technology Inc. MCP6546/6R/6U/7/8/9 = +1.6V to +5.5V GND 65% 60% 55% 50 45% 40% V 35% DD 30% 25% 20% = 5.5V 15% 10 FIGURE 2-28: Delay. ...
Page 10
... PHL 100 FIGURE 2-35: Capacitance. 1.E+04 10n 1.E+ 100p PHL 1.E+02 1.E+01 10p 1.E+ PLH 1.E-01 100f FIGURE 2-36: ( vs. Output Voltage (MCP6548 only +25° /2, V – = GND PHL t PLH Common Mode Input Voltage (V) Propagation Delay vs. = 5.5V PLH DD = 5.5V t PHL ...
Page 11
... Low-to-High 100p 1.E-10 10p 1.E-11 1.2 1.4 1.6 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 FIGURE 2-40: through current) vs. Chip Select (CS) Voltage 5.5V (MCP6548 only). DD 1.6 200 180 0.0 160 140 -1.6 120 -3.2 100 ...
Page 12
... Non-inverting Input (comparator C) Negative Power Supply Non-inverting Input (comparator D) Inverting Input (comparator D) Digital Output (comparator D) Chip Select No Internal Connection and 1. For SS , except the output pins which connected connected to the supply. V will DD pin. These can share a DD © 2006 Microchip Technology Inc. ...
Page 13
... Diodes D and D prevent the input 1 2 pin (V + and V –) from going too far above When implemented as shown, resistors R limit the current through D and © 2006 Microchip Technology Inc. MCP6546/6R/6U/7/8 ≥ FIGURE 4- also possible to connect the diodes to the left of the resistors R and R 1 ...
Page 14
... See Figures 2-15, 2-18 and 2-37 through 2-41, for more information. 4.3 MCP6548 Chip Select (CS) The MCP6548 is a single comparator with a Chip Select (CS) pin. When CS is pulled high, the total current consumption drops (typ.). 1 pA (typ.) flows through the CS pin (typ.) flows through the output pin and 18 pA (typ ...
Page 15
... DD capacitor (i.e., 0.01 µF to 0.1 µF) within 2 mm for good edge rate performance. © 2006 Microchip Technology Inc. MCP6546/6R/6U/7/8/9 4.6 Capacitive Loads Reasonable capacitive loads (e.g., logic gates) have little impact on propagation delay (see ...
Page 16
... The wired-OR connection produces a high output (logic 1) when the input voltage is between V and FIGURE 4-10: Figure 4-9 shows MCP6546 2 OUT V REF Precise Inverting (where V > 1/2 MCP6547 OUT 1/2 MCP6547 Windowed Comparator. © 2006 Microchip Technology Inc. ...
Page 17
... Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. © 2006 Microchip Technology Inc. MCP6546/6R/6U/7/8/9 I-Temp E-Temp Device ...
Page 18
... YYWWNNN 14-Lead SOIC (150 mil) (MCP6549) XXXXXXXXXX XXXXXXXXXX YYWWNNN 14-Lead TSSOP (MCP6549) XXXXXXXX YYWW NNN DS21714E-page 18 Example: MCP6549-I/P XXXXXXXXXXXXXX 0636256 MCP6549E 0636256 MCP6549 I/P 0636256 Example: MCP6549ISL XXXXXXXXXX 0636256 MCP6549 E/SL 0636256 Example: MCP6549I 0636 256 © 2006 Microchip Technology Inc. ...
Page 19
... Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .005" (0.127mm) per side. BSC: Basic Dimension. Theoretically exact value shown without tolerances. See ASME Y14.5M JEITA (EIAJ) Standard: SC-70 Drawing No. C04-061 © 2006 Microchip Technology Inc. MCP6546/6R/6U/7/8 ...
Page 20
... A2 MILLIMETERS MIN NOM MAX 6 0.95 BSC 1.90 BSC 0.90 1.18 1.45 0.90 1.10 1.30 0.00 0.08 0.15 2.60 2.80 3.00 1.50 1.63 1.75 2.80 2.95 3.10 0.35 0.45 0. 0.09 0.15 0.20 0.35 0.43 0. Revised 09-12-05 © 2006 Microchip Technology Inc. ...
Page 21
... Mold Draft Angle Bottom * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MS-001 Drawing No. C04-018 © 2006 Microchip Technology Inc. MCP6546/6R/6U/7/8 ...
Page 22
... A2 NOM MAX 8 1.27 1.55 1.75 1.42 1.55 0.18 0.25 6.02 6.20 3.91 3.99 4.90 5.00 0.38 0.51 0.62 0. 0.23 0.25 0.42 0. © 2006 Microchip Technology Inc. ...
Page 23
... Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. BSC: Basic Dimension. Theoretically exact value shown without tolerances. See ASME Y14.5M REF: Reference Dimension, usually without tolerance, for information purposes only. See ASME Y14.5M JEDEC Equivalent: MO-187 Drawing No. C04-111 © 2006 Microchip Technology Inc. MCP6546/6R/6U/7/8 φ A ...
Page 24
... A2 L NOM MAX 14 2.54 3.94 4.32 3.30 3.68 7.94 8.26 6.35 6.60 19.05 19.30 3.30 3.43 0.29 0.38 1.46 1.78 0.46 0.56 9.40 10. © 2006 Microchip Technology Inc. ...
Page 25
... Mold Draft Angle Bottom * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MS-012 Drawing No. C04-065 © 2006 Microchip Technology Inc. MCP6546/6R/6U/7/8 φ ...
Page 26
... REF 12° REF Revised: 08-17-05 © 2006 Microchip Technology Inc. ...
Page 27
... Added Section 3.0 “Pin Descriptions”. 6. Corrected package markings “Package Marking Information”). 7. Added Appendix A: “Revision History”. Revision C (May 2003) Revision B (December 2002) Revision A (February 2002) • Original Release of this Document. © 2006 Microchip Technology Inc. MCP6546/6R/6U/7/8/9 on unused (Section 5.1 DS21714E-page 27 ...
Page 28
... MCP6546/6R/6U/7/8/9 NOTES: DS21714E-page 28 © 2006 Microchip Technology Inc. ...
Page 29
... MCP6547: Dual Comparator MCP6547T: Dual Comparator (Tape and Reel for SOIC and MSOP) MCP6548: Single Comparator with CS MCP6548T: Single Comparator with CS (Tape and Reel for SOIC and MSOP) MCP6549: Quad Comparator MCP6549T: Quad Comparator (Tape and Reel for SOIC and TSSOP) ...
Page 30
... MCP6546/6R/6U/7/8/9 NOTES: DS21714E-page 30 © 2006 Microchip Technology Inc. ...
Page 31
... Select Mode, Smart Serial, SmartTel, Total Endurance, UNI/O, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 32
... Fax: 886-3-572-6459 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2006 Microchip Technology Inc. EUROPE Austria - Wels Tel: 43-7242-2244-3910 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 ...