5555164-4 TE Connectivity, 5555164-4 Datasheet - Page 4

• Manufacturer Part Number: 5555164-4
• Manufacturer: TE Connectivity

Specifications of 5555164-4

• Product Type: Connector
• Jack Type: RJ45
• Pcb Mounting Orientation: Side Entry (Right Angle)
• Pcb Mount Style: Through Hole
• Termination Method To Pc Board: Solder
• Performance Category: Cat 3
• Number Of Contacts Loaded: 8
• Grounding Options: Without
• Panel Stops: Without
• Keyed: No
• Profile: Low
• Color: Black
• Latch Style: Standard
• Jack Configuration: 1 x 1
• Panel Mount Retention: With
• Flanged: No
• Shielded: No
• Solder Tail Contact Plating: Tin over Nickel
• Height (mm [in]): 12.70 [0.500]
• Port Configuration: Single
• Number Of Positions: 8
• Inverted Jack Face: No
• Led: Without
• Pcb Tail Length (mm [in]): 3.80 [0.150]
• Preloaded: Yes
• Contact Plating, Mating Area, Material: Gold (50)
• Contact Base Material: Phosphor Bronze
• Housing Material: PBT - GF
• Ul Flammability Rating: UL 94V-0
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
• Rohs/elv Compliance History: Always was RoHS compliant
• Pcb Thickness, Recommended (mm [in]): 1.57 [0.062]
• Packaging Method: Tube

Surge.
Vibration.
Durability.
Mating and unmating forces.
Plug retention in jack.
Pull.
Jack retention to PCB.
Thermal shock.
High humidity/temperature cycling.
Rev G
Test Description
No evidence of physical damage.
No discontinuities greater than 1
microsecond.
Shall remain mated and show no
evidence of physical damage.
No evidence of physical damage.
Five pounds maximum for
unshielded plug and jack.
Eight pounds maximum for shielded
plug and jack.
Plug shall not dislodge from jack.
Plug shall remain mated with no
evidence of damage.
Jack shall not dislodge from PCB.
One pound minimum before flow
soldering.
Ten pounds minimum after flow
soldering.
No evidence of physical damage.
No evidence of physical damage.
ENVIRONMENTAL
MECHANICAL
Figure 1 (end)
Requirement
Subject mated plug and jack
adjacent contacts to 5 surges of
each polarity at 1 minute intervals.
Pulse to have 10/1000 microsecond
shape and 1000 volt peak.
EIA-364-28, Test Condition I.
Subject mated plug and jack
mounted on PCB to sinusoidal
vibration for 15 minutes in each of 3
mutually perpendicular axis.
EIA-364-9.
Subject plug and jack to 750 mating
and unmating cycles at the rate of
500 cycles per hour with latch
inoperative.
EIA-364-13.
Measure force required to mate
plug and jack. Measure force
required to unmate plug and jack
with latch depressed.
EIA-364-98.
Apply axial load of 20 pounds to
plug housing at a rate of .5 inch per
minute with plug mated in jack and
latch engaged.
Load cable in mated plug with a 17
pound pull in axial direction, rotate
plug housing 45 degrees from cable
axis, remove load.
See Figure 4.
Apply perpendicular load at a rate of
2 inches per minute to the jack
mounted on a .062 inch thick PCB.
See Figure 4.
EIA-364-32.
Subject mated plug and jack to 25
cycles between -40 and 60° C.
TE Spec 109-76-2.
Subject mated plug and jack to 10
humidity/temperature cycles
between 4 and 60° C at 95% RH.
Procedure
108-1163
4 of 7