120672-1 TE Connectivity, 120672-1 Datasheet

120672-1

Manufacturer Part Number
120672-1
Description
Manufacturer
TE Connectivity
Datasheets

Specifications of 120672-1

Product Type
Connector
Connector Type
Header
Pcb Mounting Orientation
Vertical
Module Type
Left
Solder Tail Contact Plating
Tin-Lead over Nickel
Termination Post Length (mm [in])
3.70 [0.146]
Card Slot Pitch (mm [in])
17.8 [0.7]
Rows Per Connector
10
Columns Per Connector
5
Number Of Signal Contacts
50
Centerline (mm [in])
2.00 [0.079]
Contact Type
Pin
Contact Style
Press Fit, Short Tail
Guide Pin Style
Universal Power Module
Contact Base Material
Phosphor Bronze
Contact Configuration
Grounding
Contact Mating Area Length (mm [in])
8.20 [0.323]
Contact Plating, Mating Area, Material
Conforms to Performance Requirements of TE Connectivity Product Specification 108-1957; Based on Telcordia GR-1217-CORE, Applications in Uncontrolled Environments
Connector Style
Plug
Housing Material
Polyester GF
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Not relevant for lead free process
Rohs/elv Compliance History
Always was RoHS compliant
1.
1.1.
1.2.
1.3.
2.
2.1.
2.2.
3.
3.1.
3.2.
©2011 Tyco Electronics Corporation,
a TE Connectivity Ltd. Company
All Rights Reserved
TE logo is a trademark.
SCOPE
Content
This specification covers performance, tests and quality requirements for the Z-PACK* HS3 dual beam
connector system. The receptacle has insert molded lead frames with ground shields between them.
The pin header is a stripline type construction with ground blades isolating signal contact columns. The
connector system utilizes press-fit termination to both the backplane and the daughtercard.
Qualification
When tests are performed on the subject product line, procedures specified in Figure 1 shall be used.
All inspections shall be performed using the applicable inspection plan and product drawing.
Qualification Test Results
Successful qualification testing on the subject product line was completed on 12Jan01. The
Qualification Test Report number for this testing is 501-501. This documentation is on file at and
available from Engineering Practices and Standards (EPS).
APPLICABLE DOCUMENTS
The following documents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the document applies. In the event of conflict between the
requirements of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between the requirements of this specification and the referenced documents,
this specification shall take precedence.
TE Connectivity (TE) Documents
!
!
!
!
Commercial Standard
EIA-364: Electrical Connector/Socket Test Procedures Including Environmental Classifications
REQUIREMENTS
Design and Construction
Product shall be of the design, construction and physical dimensions specified on the applicable product
drawing.
Materials
Materials used in the construction of this product shall be as specified on the applicable product
drawing.
108-1751: Product Specification
109-197: TE Test Specifications vs EIA and IEC Test Methods
114-13020: Application Specification
501-501: Qualification Test Report
| Indicates change
*Trademark
Product
Specification
Z-PACK* HS3 Dual Beam Connector System
For latest revision, visit our website at www.te.com/documents.
For Regional Customer Service, visit our website at www.te.com
Other products, logos, and company names might be trademarks of their respective owners.
108-1957
11Mar11 Rev C
1 of 7
LOC B

Related parts for 120672-1

120672-1 Summary of contents

Page 1

... Materials Materials used in the construction of this product shall be as specified on the applicable product drawing. ©2011 Tyco Electronics Corporation, | Indicates change a TE Connectivity Ltd. Company *Trademark All Rights Reserved TE logo is a trademark. For latest revision, visit our website at www.te.com/documents. For Regional Customer Service, visit our website at www.te.com Other products, logos, and company names might be trademarks of their respective owners ...

Page 2

Ratings ! Voltage: 250 volts AC ! Current: 1.15 ampere (100% loaded) ! Temperature: -65 to 105° Characteristic Impedance: 50 ohms (single ended), 100 ohms (differential) 3.4. Performance and Test Description Product is designed to meet the ...

Page 3

Test Description Vibration, sinusoidal. Mechanical shock, specified pulse. Durability. Mating force. Unmating force. Compliant pin insertion force. Compliant pin retention force. Minute disturbance. Thermal shock. Rev C Requirement MECHANICAL No discontinuities of 1 microsecond or longer duration. See Note. No ...

Page 4

Test Description Humidity-temperature cycling. Temperature life. Mixed flowing gas (unmated). Mixed flowing gas (mated). Dust contamination. Shall meet visual requirements, show no physical damage, and meet requirements of additional NOTE tests as specified in the Product Qualification and Requalification Test ...

Page 5

Product Qualification and Requalification Test Sequence Test or Examination Initial examination of product Dry circuit resistance Change in resistance Insulation resistance Dielectric withstanding voltage Compliant pin resistance Vibration Mechanical shock Durability Mating force Unmating force Compliant pin insertion force ...

Page 6

QUALITY ASSURANCE PROVISIONS 4.1. Qualification Testing A. Specimen Selection Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be selected at random from current production. All test groups shall each consist of a minimum of 5 ...

Page 7

Vibration & Mechanical Shock Mounting Fixture Rev C Figure 3 Dry Circuit Resistance Measurement Points Figure 4 108-1957 ...

Related keywords