LH79524_LH79525_N NXP Semiconductors, LH79524_LH79525_N Datasheet - Page 28
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
LH79524_LH79525_N
Manufacturer Part Number
LH79524_LH79525_N
Description
The LH79524/LH79525, powered by an ARM720T,is a complete System-on-Chip with a high level of integrationto satisfy a wide range of requirements andapplications
Manufacturer
NXP Semiconductors
Datasheet
1.LH79524_LH79525_N.pdf
(64 pages)
LH79524/LH79525
Power Supply Sequencing
ommends that the 1.8 V power supply be energized
before the 3.3 V supply. If this is not possible, the 1.8 V
supply may not lag the 3.3 V supply by more than 100
µs. If longer delay time is needed, it is recommended
that the voltage difference between the two power sup-
plies be within 1.5 V during power supply ramp up. To
avoid a potential latchup condition, voltage should be
applied to input pins only after the device is powered-
on as described above.
DC SPECIFICATIONS
NOTES:
1. Table 2 details each pin’s buffer type.
2. Running Typical Application over operating range.
3. Current measured with CPU stopped and all peripherals enabled
Linear Regulator DC Characteristics.
28
VIH
VIL
VIT+
VIT-
VHYST
VOH
VOL
RIN
IACTIVE
ISTANDBY Standby current
ISLEEP
ISTOP1
ISTOP2
ISTOP2
ISTOP2
ISTOP2
IQUIESCENT Quiescent Current
ISLEEPLR
IOLR
VOLR
SYMBOL
When the linear regulator is not enabled, NXP rec-
SYMBOL
1
1
CMOS input HIGH voltage
CMOS input LOW voltage
Positive Input threshold voltage (Schmitt pins)
Negative Input threshold voltage (Schmitt pins)
Schmitt trigger hysteresis
Output drive (2 mA type)
Output drive (4 mA type)
Output drive (8 mA type)
Output drive (12 mA type)
Output drive (2 mA type)
Output drive (4 mA type)
Output drive (8 mA type)
Output drive (12 mA type)
Input leakage pull-up/pull-down resistors
Active current
Sleep current
Stop1 current
Stop2 current
Stop2 current
Stop2 current
Stop2 current
Current with Linear Regulator disabled
Output Current Range
Output Voltage, Linear Regulator
PARAMETER
PARAMETER
NXP Semiconductors
Rev. 01 — 16 July 2007
MIN. TYP. MAX. UNIT
0.0
MIN. TYP. MAX. UNIT
2.6
2.6
2.0
2.0
2.6
2.6
2.6
1.84
75
8
DC/AC Specifications
• -40°C to +85°C (Industrial temperature range)
• VDDC = 1.7 V to 1.9 V
• VDD = 3.0 V to 3.6 V, VDDA = 1.7 V to 1.9 V.
0.35
Unless noted, all data provided are based on:
420
115
3.8
40
85
50
95
45
25
200
5.5
0.8
0.4
0.4
0.4
0.8
mA
µA
µA
V
mA
mA
mA
kΩ
µA
µA
µA
µA
µA
V
V
V
V
V
V
V
V
V
V
V
V
V
CSEN = 1
IOH = -8 mA
IOH = -12 mA
IOH = 12 mA
CEN = 1
CEN = 1
CSEN = 1
CSEN = 1
IOH = -2 mA
IOH = -4 mA
IOL = 2 mA
IOL = 4 mA
IOL = 7 mA
VIN = VDD or GND (Calculate input
leakage current at desired VDD)
Note 2
Notes 2, 3
RTC ON, Linear Regulator ON
RTC OFF, Linear Regulator ON
RTC ON, Linear Regulator OFF
RTC OFF, Linear Regulator OFF
Preliminary data sheet
CONDITIONS
System-on-Chip