AD5532HS Analog Devices, AD5532HS Datasheet
AD5532HS
Specifications of AD5532HS
Available stocks
Related parts for AD5532HS
AD5532HS Summary of contents
Page 1
... SS put amplifier. The device is operated with and requires a stable 2.5 V reference on REF_IN. PRODUCT HIGHLIGHTS 1. 32 14-bit DACs in one package, guaranteed monotonic. 2. The AD5532HS is available in a 74-ball LFBGA package with a body size mm. FUNCTIONAL BLOCK DIAGRAM DV AV REF_IN CC CC ...
Page 2
... A Version: Industrial temperature range –40°C to +85°C; typical at 25°C. 3 Guaranteed by design and characterization, not production tested. 4 Output range is restricted from AD780 as reference for the AD5532HS. 6 Outputs unloaded. Specifications subject to change without notice 5.25 V; AGND = DGND = DAC_GND = 0 V; REF_IN = unless otherwise noted ...
Page 3
... Figure 1. Serial Interface Timing Diagram –3– AD5532HS = 5.25 V; AGND = unless otherwise noted.) MAX Conditions/Comments 100 pF, 5 kΩ Load; Full-Scale Change 1 LSB Change around Major Carry = 5.25 V ...
Page 4
... ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD5532HS features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality ...
Page 5
... VO18 C2 DAC_GND1 C6 N/C REV. 0 PIN CONFIGURATION TOP VIEW AD5532HS 74-Ball (LFBGA) Configuration LFBGA Ball Number Name C10 AVCC1 C11 N/C D1 VO20 D2 DAC_GND2 D10 AVCC2 D11 N/C E1 VO26 E2 VO14 E10 AGND1 E11 OFFS_IN F1 VO25 F2 VO21 ...
Page 6
... AD5532HS Pin Function AGND (1–2) Analog GND Pins. AV (1–2) Analog Supply Pins. Voltage range from 4. 5. (1–4) V Supply Pins. Voltage range from (1–4) V Supply Pins. Voltage range from –4. – DGND Digital GND Pins. ...
Page 7
... OFFS_IN –1 TIME BASE – 1.25 s/DIV TPC 5. Full-Scale Settling Time TPC 8. Offset Error Distribution at 25 ° C –7– AD5532HS 5.000 V = 2.5V REFIN OFFS_IN DAC LOADED TO FULL SCALE 4.995 4.990 4.985 – TEMPERATURE – C TPC 3. V vs. Temperature OUT 2 ...
Page 8
... OUT Reset Function The reset function on the AD5532HS can be used to reset all nodes on the device to their power-on-reset condition. All the DACs are loaded with 0s and all registers are cleared. The reset function is implemented by taking the RESET pin low. ...
Page 9
... SPI Control Register (SPCR)—see 68HC11 User Manual. SCK of the 68HC11 drives the SCLK of the AD5532HS and the MOSI output drives the serial data line ) of the AD5532HS. The SYNC signal is derived from a port (D IN line (PC7). When data is being transmitted to the AD5532HS, the SYNC line is taken low (PC7) ...
Page 10
... DACs to perform a control and measurement function. In the circuit shown in Figure 7, the 0 V–5 V outputs of the AD5532HS are amplified to a range of 0 V–180 V and then used to control actuators that determine the position of MEMS mirrors in an optical switch. The exact position of each mirror is measured using sensors ...
Page 11
... BSC 0.472 (12.00) BSC 0.472 (12.00) TOP VIEW 0.039 BSC (1.00) BSC 0.039 (1.00) BSC DETAIL A DETAIL A 0.020 (0.50) MIN 0.024 (0.60) BSC BALL DIAMETER –11– AD5532HS 0.394 BOTTOM (10.00) F VIEW BSC 0.033 (0.85) MIN SEATING PLANE ...
Page 12
–12– ...