AD6654 Analog Devices, AD6654 Datasheet - Page 29
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD6654
Manufacturer Part Number
AD6654
Description
14-Bit, 92.16 MSPS, 4 & 6-Channel Wideband IF to Base Band Receiver
Manufacturer
Analog Devices
Datasheet
1.AD6654.pdf
(88 pages)
Specifications of AD6654
Resolution (bits)
14bit
# Chan
1
Sample Rate
92.16MSPS
Interface
Par
Analog Input Type
Diff-Uni
Adc Architecture
Subranging
Pkg Type
BGA,CSP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD6654BBC
Manufacturer:
AD
Quantity:
13 888
Company:
Part Number:
AD6654BBC
Manufacturer:
ADI
Quantity:
280
Company:
Part Number:
AD6654BBC
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD6654BBC
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD6654BBCZ
Manufacturer:
ADI
Quantity:
853
Company:
Part Number:
AD6654BBCZ
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Company:
Part Number:
AD6654CBC
Manufacturer:
ADI
Quantity:
283
Company:
Part Number:
AD6654CBC
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD6654CBC
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD6654CBCZ
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD6654CBCZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD6654XBC
Manufacturer:
ADI
Quantity:
284
Part Number:
AD6654XBCZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
DDC CONFIGURATION NOTES
PLL Clock Multiplier
In the AD6654, the input clock rate must be the same as the
input data rate. In a typical digital down-converter architecture,
the clock rate is a limitation on the number of filter taps that
can be calculated in the programmable RAM coefficient filters
(MRCF, DRCF, and CRCF). For slower ADC clock rates (or for
any clock rate), this limitation can be overcome by using a PLL
clock multiplier to provide a higher clock rate to the RCF filters.
Using this clock multiplier, the internal signal processing clock
rate can be increased up to 200 MHz. The CLK signal is used as
an input to the PLL clock multiplier.
The PLL clock multiplier is programmable and uses the input
clock rates between 30 MHz and 92.16 MHz to give a system
clock rate (output) of as high as 200 MHz.
The output clock rate is given by
where:
CLK is the input port clock rate.
M is a 5-bit programmable multiplication factor.
BALANCE
SOURCE
SINGLE-
SOURCE
ENDED
CLK
50Ω
PLL
50Ω
Figure 41. ADC Driving Application Using Single-Ended Input
Figure 40. ADC Driving Application Using Differential Input
PLL CLOCK GENERATION
_
(1, 2, 4 OR 8)
DIVIDE BY N
CLK
2
R1
25Ω
25Ω
25Ω
25Ω
N
100nF
100nF
100nF
=
Figure 42. PLL Clock Generation
CLK
100nF
R
R
INLO
INLO
G
G
PLL CLOCK
INHI
MULTIPLIER
INHI
N
(4x TO 20x)
×
5
M
R
AD8351
AD8351
M
F
BYPASS_PLL
1 FOR BYPASS
V
V
OPHI
OPHI
OCM
OCM
OPLO
OPLO
1
0
0
1
25Ω
25Ω
25Ω
25Ω
100nF
100nF
AIN+
AIN–
AIN+
AIN–
AD6654
AD6654
V
V
REF
REF
ADC_CLK
PLL_CLK
DIGITAL
DIGITAL
OUT
OUT
Rev. 0 | Page 29 of 88
N is a predivide factor and can be 1, 2, 4, or 8.
M is a 5-bit number between 4 and 20 (inclusive).
The multiplication factor, M, is programmed using a 5-bit PLL
clock multiplier word in the ADC clock control register. A value
outside the valid range of 4 to 20 bypasses the PLL clock
multiplier and, therefore, the PLL clock is the same as the input
clock. The predivide factor, N, is programmed using a 2-bit
ADC pre-PLL clock divider word in the ADC clock control
register, as listed in Table 13.
Table 13. PLL Clock Generation Predivider Control
Predivide Word [1:0]
00
01
10
11
For best signal processing advantage, the user should program
the clock multiplier to give a system clock output as close as
possible to, but not exceeding, 200 MHz. The internal blocks of
the AD6654 that run off the PLL clock are rated to run at a
maximum of 200 MHz. The default power-up state for the PLL
clock multiplier is the bypass state, where CLK is passed on as
the PLL clock.
ADC Gain Control
The DDC input port has individual, high speed gain control
logic circuitry. Such gain control circuitry is useful in applica-
tions that involve large dynamic-range inputs. The AD6654 gain
control logic allows programmable upper and lower thresholds
and a programmable dwell-time counter for temporal
hysteresis.
The DDC input port has a 3-bit output from the gain control
block. The operation is controlled by the gain control enable bit
in the gain control register of the DDC input port. Logic 1 in
this bit programs the EXP[2:0] pins as gain control outputs.
Function
The gain control block features a programmable upper thresh-
old register and a lower threshold register. The ADC input data
is compared to both these registers. If ADC input data is larger
than the upper threshold register, then the gain control output
is decremented by 1. If the ADC input data is smaller than the
lower threshold register, then the gain control output is incre-
mented by 1.
When decrementing the gain control output, the change is
immediate. But when incrementing the output, a dwell-time
register is used to delay the change. If the ADC input is larger
than the upper threshold register value, the gain control output
is immediately decremented to prevent overflow.
When the ADC input is lower than the lower threshold register,
a dwell timer is loaded with the value in the programmable
20-bit dwell-time register. The counter decrements once every
Divide-By Value for the Clock
Divide-by-1, bypass
Divide-by-2
Divide-by-4
Divide-by-8
AD6654