AD7324 Analog Devices, AD7324 Datasheet - Page 16

• Manufacturer Part Number: AD7324
• Description: Software Selectable True Bipolar Input, 4-Channel, 12-Bit Plus Sign A/D Converter
• Manufacturer: Analog Devices

Specifications of AD7324

• Resolution (bits): 13bit
• # Chan: 4
• Sample Rate: 1MSPS
• Interface: Ser,SPI
• Analog Input Type: Diff-Bip,Diff-Uni,SE-Uni
• Ain Range: Bip (Vref),Bip (Vref) x 2,Bip (Vref) x 4,Bip 10V,Bip 2.5V,Bip 5.0V,Uni (Vref) x 4,Uni 10V
• Adc Architecture: SAR
• Pkg Type: SOP

AD7324
THEORY OF OPERATION
CIRCUIT INFORMATION
The AD7324 is a fast, 4-channel, 12-bit plus sign, bipolar input,
serial ADC. The AD7324 can accept bipolar input ranges that
include ±10 V, ±5 V, and ±2.5 V; it can also accept a 0 V to +10 V
unipolar input range. A different analog input range can be
programmed on each analog input channel via the on-chip
registers. The AD7324 has a high speed serial interface that can
operate at throughput rates up to 1 MSPS.
The AD7324 requires V
analog input structures. These supplies must be equal to or greater
than the analog input range. See Table 6 for the requirements of
these supplies for each analog input range. The AD7324 requires
a low voltage 2.7 V to 5.25 V V
Table 6. Reference and Supply Requirements for Each Analog
Input Range
Selected
Analog Input
Range (V)
±10
±5
±2.5
0 to +10
To meet the specified performance specifications when the
AD7324 is configured with the minimum V
for a chosen analog input range, the throughput rate should be
decreased from the maximum throughput range (see the
Typical Performance Characteristics section). Figure 18 and
Figure 19 show the change in INL and DNL as the V
voltages are varied. When operating at the maximum throughput
rate, as the V
and DNL error increases. However, as the throughput rate is
reduced with the minimum V
DNL error is reduced.
Figure 31 shows the change in THD as the V
are reduced. At the maximum throughput rate, the THD degrades
significantly as V
to reduce the throughput rate when using minimum V
V
specified performance can be maintained. The degradation is
due to an increase in the on resistance of the input multiplexer
when the V
SS
supplies so that there is less degradation of THD and the
DD
DD
and V
and V
DD
Reference
Voltage (V)
2.5
3.0
2.5
3.0
2.5
3.0
2.5
3.0
and V
SS
SS
supplies are reduced.
DD
supply voltages are reduced, the INL
and V
SS
are reduced. It is, therefore, necessary
DD
CC
SS
Full-Scale
Input
Range (V)
±10
±12
±5
±6
±2.5
±3
0 to +10
0 to +12
supply to power the ADC core.
and V
dual supplies for the high voltage
SS
supplies, the INL and
DD
AV
3/5
3/5
3/5
3/5
3/5
3/5
3/5
3/5
DD
and V
CC
and V
(V)
DD
SS
SS
Minimum
V
±10
±12
±5
±6
±5
±5
+10/AGND
+12/AGND
supplies
DD
and V
supplies
DD
and
/V
SS
Rev. A | Page 16 of 36
SS
(V)
The analog inputs can be configured as four single-ended
inputs, two true differential input pairs, two pseudo differential
inputs, or three pseudo differential inputs. Selection can be
made by programming the mode bits, Mode 0 and Mode 1, in
the control register.
The serial clock input accesses data from the part and provides
the clock source for the successive approximation ADC. The
AD7324 has an on-chip 2.5 V reference. However, the AD7324
can also work with an external reference. On power-up, the
external reference operation is the default option. If the internal
reference is the preferred option, the user must write to the
reference bit in the control register to select the internal
reference operation.
The AD7324 also features power-down options to allow power
saving between conversions. The power-down modes are
selected by programming the on-chip control register as
described in the Modes of Operation section.
CONVERTER OPERATION
The AD7324 is a successive approximation ADC built around
two capacitive DACs. Figure 23 and Figure 24 show simplified
schematics of the ADC in single-ended mode during the
acquisition and conversion phases, respectively. Figure 25 and
Figure 26 show simplified schematics of the ADC in differential
mode during acquisition and conversion phases, respectively.
The ADC is composed of control logic, a SAR, and capacitive
DACs. In Figure 23 (the acquisition phase), SW2 is closed and
SW1 is in Position A, the comparator is held in a balanced
condition, and the sampling capacitor array acquires the signal
on the input.
When the ADC starts a conversion (Figure 24), SW2 opens and
SW1 moves to Position B, causing the comparator to become
unbalanced. The control logic and the charge redistribution
DAC are used to add and subtract fixed amounts of charge from
the capacitive DAC to bring the comparator back into a
balanced condition. When the comparator is rebalanced, the
conversion is complete. The control logic generates the ADC
output code.
V
V
IN
IN
0
0
Figure 23. ADC Acquisition Phase (Single-Ended)
Figure 24. ADC Conversion Phase (Single-Ended)
AGND
AGND
B
B
A
A
SW1
SW1
C
C
S
S
SW2
SW2
COMPARATOR
COMPARATOR
CAPACITIVE
CAPACITIVE
CONTROL
CONTROL
LOGIC
LOGIC
DAC
DAC