SAM7X256 Atmel Corporation, SAM7X256 Datasheet - Page 99

• Manufacturer Part Number: SAM7X256
• Manufacturer: Atmel Corporation

Specifications of SAM7X256

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 62
• Ext Interrupts: 62
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 3
• Can: 1
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

3.7
3.7.1
3.7.2
ARM DDI 0029G
Stretching access times
Modulating MCLK
Use of nWAIT to control bus cycles
The ARM7TDMI processor does not contain any dynamic logic that relies on regular
clocking to maintain the internal state. Therefore, there is no limit upon the maximum
period for which MCLK can be stretched, or nWAIT held LOW. There are two
methods available to stretch access times as described in:
•
•
If you wish to use an Embedded Trace Macrocell (ETM) to obtain instruction and data
trace information on a trace port then you must use the nWAIT signal to stretch access
times.
All memory timing is defined by MCLK, and long access times can be accommodated
by stretching this clock. It is usual to stretch the LOW period of MCLK, as this allows
the memory manager to abort the operation if the access is eventually unsuccessful.
MCLK can be stretched before being applied to the processor, or the nWAIT input can
be used together with a free-running MCLK. Taking nWAIT LOW has the same effect
as stretching the LOW period of MCLK.
The pipelined nature of the processor bus interface means that there is a distinction
between clock cycles and bus cycles. nWAIT can be used to stretch a bus cycle, so that
it lasts for many clock cycles. The nWAIT input allows the timing of bus cycles to be
extended in increments of complete MCLK cycles:
•
•
nWAIT must only change during the LOW phase of MCLK.
In the pipeline, the address class signals and the memory request signals are ahead of
the data transfer by one bus cycle. In a system using nWAIT this can be more than one
MCLK cycle. This is illustrated in Figure 3-21 on page 3-30, which shows nWAIT
being used to extend a nonsequential cycle. In the example, the first N-cycle is followed
a few cycles later by another N-cycle to an unrelated address, and the address for the
second access is broadcast before the first access completes.
Modulating MCLK on page 3-29
Use of nWAIT to control bus cycles on page 3-29.
when nWAIT is HIGH on the falling edge of MCLK, a bus cycle completes
when nWAIT is LOW, the bus cycle is extended by stretching the low phase of
the internal clock.
Note
Copyright © 1994-2001. All rights reserved.
Memory Interface
3-29