SAM7S128 Atmel Corporation, SAM7S128 Datasheet - Page 102
SAM7S128
Manufacturer Part Number
SAM7S128
Description
Manufacturer
Atmel Corporation
Specifications of SAM7S128
Flash (kbytes)
128 Kbytes
Pin Count
64
Max. Operating Frequency
55 MHz
Cpu
ARM7TDMI
Hardware Qtouch Acquisition
No
Max I/o Pins
32
Ext Interrupts
32
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
1
Twi (i2c)
1
Uart
3
Ssc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
384
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
32
Self Program Memory
NO
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
3.0 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- Current page: 102 of 284
- Download datasheet (2Mb)
Memory Interface
3.9
3-32
Privileged mode access
ARM Limited usually recommends that if only privileged mode access is required from
a memory system then you are advised to use the nTRANS pin on the core. This signal
distinguishes between User and privileged accesses.
The reason that this is recommended is that if the Operating System (OS) accesses
memory on behalf of the current application then it must perform these accesses in User
mode. This is achieved using the LDRT and STRT instructions that set nTRANS
appropriately.
This measure avoids the possibility of a hacker deliberately passing an invalid pointer
to an OS and getting the OS to access this memory with privileged access. This
technique could otherwise be used by a hacker to enable the user application to access
any memory locations such as I/O space.
The least significant five bits of the CPSR are also output from the core as inverted
signals, nM[4:0]. These indicate the current processor mode as listed in Table 3-8.
The only time to use the nM[4:0] signals is for diagnostic and debug purposes.
Note
Copyright © 1994-2001. All rights reserved.
Table 3-8 Use of nM[4:0] to indicate current processor mode
M[4:0]
10000
10001
10010
10011
10111
11011
11111
nM[4:0]
01111
01110
01101
01100
01000
00100
00000
ARM DDI 0029G
Mode
User
FIQ
IRQ
Supervisor
Abort
Undefined
System
Related parts for SAM7S128
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: