SAM7S128 Atmel Corporation, SAM7S128 Datasheet - Page 291
SAM7S128
Manufacturer Part Number
SAM7S128
Description
Manufacturer
Atmel Corporation
Specifications of SAM7S128
Flash (kbytes)
128 Kbytes
Pin Count
64
Max. Operating Frequency
55 MHz
Cpu
ARM7TDMI
Hardware Qtouch Acquisition
No
Max I/o Pins
32
Ext Interrupts
32
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
1
Twi (i2c)
1
Uart
3
Ssc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
384
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
32
Self Program Memory
NO
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
3.0 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- Current page: 291 of 781
- Download datasheet (12Mb)
29. Two-wire Interface (TWI) SAM7S512/256/128/64/321/32
29.1
29.2
6175L–ATARM–28-Jul-11
Overview
List of Abbreviations
NOTE: This definition of the TWI does not pertain to SAM7S16/161. For SAM7S16/161, see
Section 30.
The Two-wire Interface (TWI) interconnects components on a unique two-wire bus, made up of
one clock line and one data line with speeds of up to 400 Kbits per second, based on a byte-ori-
ented transfer format. It can be used with any Atmel Two-wire Interface bus Serial EEPROM and
I²C compatible device such as Real Time Clock (RTC), Dot Matrix/Graphic LCD Controllers and
Temperature Sensor, to name but a few. The TWI is programmable as master transmitter or
master receiver with sequential or single-byte access. A configurable baud rate generator per-
mits the output data rate to be adapted to a wide range of core clock frequencies. Below,
29-1
Table 29-1.
Notes:
Table 29-2.
I2C Standard
Standard Mode Speed (100 KHz)
Fast Mode Speed (400 KHz)
7 or 10 bits Slave Addressing
START BYTE
Repeated Start (Sr) Condition
ACK and NACK Management
Slope control and input filtering (Fast mode)
Clock stretching
Abbreviation
TWI
A
N
P
S
Sr
DADR
IADR
R
W
lists the compatibility level of the Atmel Two-wire Interface and a full I2C compatible device.
1. START + b000000001 + Ack + Sr
2. A repeated start condition is only supported in Master Receiver mode. See
“Internal Address” on page 297
(1)
Atmel TWI compatibility with i2C Standard
Abbreviations
Description
Two-wire Interface
Acknowledge
Not Acknowledge
Stop
Start
Repeated Start
Device Address
Internal Address
Read
Write
Atmel TWI
Supported
Supported
Supported
Not Supported
Not Fully Supported
Supported
Not Supported
Supported
(2)
SAM7S Series
Section 29.6.5
Table
291
Related parts for SAM7S128
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: