ATtiny85 Atmel Corporation, ATtiny85 Datasheet - Page 3

no-image

ATtiny85

Manufacturer Part Number
ATtiny85
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATtiny85

Flash (kbytes)
8 Kbytes
Pin Count
8
Max. Operating Frequency
20 MHz
Cpu
8-bit AVR
# Of Touch Channels
3
Hardware Qtouch Acquisition
No
Max I/o Pins
6
Ext Interrupts
6
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
4
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
0.5
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
5
Pwm Channels
6
32khz Rtc
No
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATtiny85-15SZ
Manufacturer:
ATMEL
Quantity:
30
Part Number:
ATtiny85-20PU
Manufacturer:
CUI
Quantity:
1 000
Part Number:
ATtiny85-20SU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATtiny85V-10SH
Manufacturer:
Intel
Quantity:
62
Part Number:
ATtiny85V-10SU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Table 1-1.
Notes:
2586N–Appendix A–AVR–08/11
Symbol
R
R
I
CC
RST
pu
1. Typical values at 25°C.
2. “Min” means the lowest value where the pin is guaranteed to be read as high.
3. “Max” means the highest value where the pin is guaranteed to be read as low.
4. Although each I/O port can sink more than the test conditions (10 mA at V
5. Although each I/O port can source more than the test conditions (10 mA at V
6. The RESET pin must tolerate high voltages when entering and operating in programming modes and, as a consequence,
7. Values are with external clock using methods described in
8. Brown-Out Detection (BOD) disabled.
conditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 60 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 60 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
has a weak drive strength as compared to regular I/O pins.
enabled (PRR = 0xFF) and there is no I/O drive.
Parameter
Reset Pull-up Resistor
I/O Pin Pull-up Resistor
Power Supply Current
Power-down mode
DC Characteristics. T
(8)
(7)
A
= -40°C to +105°C (Continued)
Condition
V
V
Active 1MHz, V
Active 4MHz, V
Active 8MHz, V
Idle 1MHz, V
Idle 4MHz, V
Idle 8MHz, V
WDT enabled, V
WDT disabled, V
CC
CC
= 5.5V, input low
= 5.5V, input low
CC
CC
CC
CC
CC
CC
= 2V
= 3V
= 5V
CC
CC
= 2V
= 3V
= 5V
= 3V
= 3V
“Minimizing Power Consumption” on page
Min.
30
20
CC
CC
= 5V, 5 mA at V
= 5V, 5 mA at V
Typ.
0.35
0.3
1.5
0.1
1.2
0.2
5
4
(1)
CC
CC
= 3V) under steady state
Max.
= 3V) under steady state
0.55
2.5
0.2
0.6
60
50
20
10
2
8
37. Power Reduction is
ATtiny25
Units
mA
mA
mA
mA
mA
mA
µA
µA
3

Related parts for ATtiny85