ATmega3290 Atmel Corporation, ATmega3290 Datasheet - Page 49

• Manufacturer Part Number: ATmega3290
• Manufacturer: Atmel Corporation

Specifications of ATmega3290

• Flash (kbytes): 32 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

11. Interrupts
11.1
2552K–AVR–04/11
Interrupt Vectors in ATmega329/3290/649/6490
T h i s s e c t i o n d e s c r i b e s t h e s p e c i f i c s o f t h e i n t e r r u p t h a n d l i n g a s p e r f o r m e d i n
ATmega329/3290/649/6490. For a general explanation of the AVR interrupt handling, refer to
“Reset and Interrupt Handling” on page
Table 11-1.
Note:
Vector
24
25
No.
10
11
12
13
14
15
16
17
18
19
20
21
22
23
1
2
3
4
5
6
7
8
9
(3)
(3)
1. When the BOOTRST Fuse is programmed, the device will jump to the Boot Loader address at
2. When the IVSEL bit in MCUCR is set, Interrupt Vectors will be moved to the start of the Boot
3. PCINT2 and PCINT3 are only present in ATmega3290 and ATmega6490.
Address
Program
0x0000
reset, see
Flash Section. The address of each Interrupt Vector will then be the address in this table
added to the start address of the Boot Flash Section.
0x000C
0x001C
0x002C
0x000A
0x000E
0x001A
0x001E
0x002A
0x002E
0x0002
0x0004
0x0006
0x0008
0x0010
0x0012
0x0014
0x0016
0x0018
0x0020
0x0022
0x0024
0x0026
0x0028
0x0030
Reset and Interrupt Vectors
(1)
(2)
“Boot Loader Support – Read-While-Write Self-Programming” on page
Source
RESET
INT0
PCINT0
PCINT1
TIMER2 COMP
TIMER2 OVF
TIMER1 CAPT
TIMER1 COMPA
TIMER1 COMPB
TIMER1 OVF
TIMER0 COMP
TIMER0 OVF
SPI, STC
USART, RX
USART, UDRE
USART, TX
USI START
USI OVERFLOW
ANALOG COMP
ADC
EE READY
SPM READY
LCD
PCINT2
PCINT3
15.
Interrupt Definition
External Pin, Power-on Reset, Brown-out Reset,
Watchdog Reset, and JTAG AVR Reset
External Interrupt Request 0
Pin Change Interrupt Request 0
Pin Change Interrupt Request 1
Timer/Counter2 Compare Match
Timer/Counter2 Overflow
Timer/Counter1 Capture Event
Timer/Counter1 Compare Match A
Timer/Counter1 Compare Match B
Timer/Counter1 Overflow
Timer/Counter0 Compare Match
Timer/Counter0 Overflow
SPI Serial Transfer Complete
USART0, Rx Complete
USART0 Data Register Empty
USART0, Tx Complete
USI Start Condition
USI Overflow
Analog Comparator
ADC Conversion Complete
EEPROM Ready
Store Program Memory Ready
Pin Change Interrupt Request 2
Pin Change Interrupt Request 3
LCD Start of Frame
ATmega329/3290/649/6490
278.
49