ATmega169P Atmel Corporation, ATmega169P Datasheet - Page 234

• Manufacturer Part Number: ATmega169P
• Manufacturer: Atmel Corporation

Specifications of ATmega169P

• Flash (kbytes): 16 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 100
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

23. LCD Controller
23.1
23.2
23.2.1
8018P–AVR–08/10
Features
Overview
Definitions
•
•
•
•
•
•
•
•
•
•
•
•
The LCD Controller/driver is intended for monochrome passive liquid crystal display (LCD) with
up to four common terminals and up to 25 segment terminals.
A simplified block diagram of the LCD Controller/Driver is shown in
the actual placement of I/O pins, see
on page
An LCD consists of several segments (pixels or complete symbols) which can be visible or non
visible. A segment has two electrodes with liquid crystal between them. When a voltage above a
threshold voltage is applied across the liquid crystal, the segment becomes visible.
The voltage must alternate to avoid an electrophoresis effect in the liquid crystal, which
degrades the display. Hence the waveform across a segment must not have a DC-component.
The PRLCD bit in
enable the LCD module.
Several terms are used when describing LCD. The definitions in
this document.
Table 23-1.
LCD
Segment
Common
Duty
Bias
Frame Rate
Display Capacity of 25 Segments and Four Common Terminals
Support Static, 1/2, 1/3 and 1/4 Duty
Support Static, 1/2, 1/3 Bias
On-chip LCD Power Supply, only One External Capacitor needed
Display Possible in Power-save Mode for Low Power Consumption
Software Selectable Low Power Waveform Capability
Flexible Selection of Frame Frequency
Software Selection between System Clock or an External Asynchronous Clock Source
Equal Source and Sink Capability to maximize LCD Life Time
LCD Interrupt Can be Used for Display Data Update or Wake-up from Sleep Mode
Segment and Common Pins not Needed for Driving the Display Can be Used as Ordinary I/O Pins
Latching of Display Data gives Full Freedom in Register Update
2.
Definitions
”PRR – Power Reduction Register” on page 45
A passive display panel with terminals leading directly to a segment
The least viewing element (pixel) which can be on or off
Denotes how many segments are connected to a segment terminal
1/(Number of common terminals on a actual LCD display)
1/(Number of voltage levels used driving a LCD display -1)
Number of times the LCD segments is energized per second.
”64A (TQFP) and 64M1 (QFN/MLF) Pinout ATmega169P”
Table 23-1
Figure 23-1 on page
must be written to zero to
ATmega169P
are used throughout
235. For
234