AT90USB1287 Atmel Corporation, AT90USB1287 Datasheet - Page 44

• Manufacturer Part Number: AT90USB1287
• Manufacturer: Atmel Corporation

Specifications of AT90USB1287

• Flash (kbytes): 128 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 48
• Ext Interrupts: 16
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Eeprom (bytes): 4096
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 10
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

6.5
44
Calibrated Internal RC Oscillator
AT90USB64/128
Note:
The calibrated internal RC Oscillator by default provides a 8.0 MHz clock. The frequency is nom-
inal value at 3V and 25°C. The device is shipped with the CKDIV8 Fuse programmed. See
“System Clock Prescaler” on page 47
clock by programming the CKSEL Fuses as shown in
no external components. During reset, hardware loads the calibration byte into the OSCCAL
Register and thereby automatically calibrates the RC Oscillator. At 3V and 25°C, this calibration
gives a frequency of 8 MHz ±10%. The oscillator can be calibrated to any frequency in the range
7.3 - 8.1 MHz within ±10% accuracy, by changing the OSCCAL register. When this Oscillator is
used as the chip clock, the Watchdog Oscillator will still be used for the Watchdog Timer and for
the Reset Time-out. For more information on the pre-programmed calibration value, see the sec-
tion
Table 6-7.
Notes:
When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Table 6-5 on page
“Calibration Byte” on page 369
1. These options should only be used if frequency stability at start-up is not important for the
1. The device is shipped with this option selected.
2. The frequency ranges are preliminary values. Actual values are TBD.
3. If 8 MHz frequency exceeds the specification of the device (depends on V
application.
Fuse can be programmed in order to divide the internal frequency by 8.
Internal Calibrated RC Oscillator Operating Modes
Frequency Range
43.
7.3 - 8.1
(2)
(MHz)
for more details. This clock may be selected as the system
Table
6-7. If selected, it will operate with
(1)(3)
CKSEL3..0
0010
CC
), the CKDIV8
7593K–AVR–11/09