AT90PWM316 Atmel Corporation, AT90PWM316 Datasheet - Page 311

• Manufacturer Part Number: AT90PWM316
• Manufacturer: Atmel Corporation

Specifications of AT90PWM316

• Flash (kbytes): 16 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 3
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 5
• Output Compare Channels: 16
• Input Capture Channels: 1
• Pwm Channels: 12
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

27. AT90PWM216/316 Typical Characteristics – Preliminary Data
7710F–AVR–09/11
Table 26-6.
Notes:
The following charts show typical behavior. These figures are not tested during manufacturing.
All current consumption measurements are performed with all I/O pins configured as inputs and
with internal pull-ups enabled. A sine wave generator with rail-to-rail output is used as clock
source.
All Active- and Idle current consumption measurements are done with all bits in the PRR register
set and thus, the corresponding I/O modules are turned off. Also the Analog Comparator is dis-
Symbol
V
I
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
PP
DVXH
XLXH
XHXL
XLDX
XLWL
XLPH
PLXH
BVPH
PHPL
PLBX
WLBX
PLWL
BVWL
WLWH
WLRL
WLRH
WLRH_CE
XLOL
BVDV
OLDV
OHDZ
PP
1. t
2. t
commands.
WLRH
WLRH_CE
Parameter
Programming Enable Voltage
Programming Enable Current
Data and Control Valid before XTAL1 High
XTAL1 Low to XTAL1 High
XTAL1 Pulse Width High
Data and Control Hold after XTAL1 Low
XTAL1 Low to WR Low
XTAL1 Low to PAGEL high
PAGEL low to XTAL1 high
BS1 Valid before PAGEL High
PAGEL Pulse Width High
BS1 Hold after PAGEL Low
BS2/1 Hold after WR Low
PAGEL Low to WR Low
BS1 Valid to WR Low
WR Pulse Width Low
WR Low to RDY/BSY Low
WR Low to RDY/BSY High
WR Low to RDY/BSY High for Chip Erase
XTAL1 Low to OE Low
BS1 Valid to DATA valid
OE Low to DATA Valid
OE High to DATA Tri-stated
Parallel Programming Characteristics, V
is valid for the Write Flash, Write EEPROM, Write Fuse bits and Write Lock bits
is valid for the Chip Erase command.
(1)
(2)
CC
= 5V ± 10%
AT90PWM216/316
Min.
11.5
200
150
150
150
150
3.7
7.5
67
67
67
67
67
67
67
0
0
0
0
0
Typ.
Max.
12.5
250
250
250
250
10
1
5
Units
μA
ms
ms
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
μs
ns
ns
ns
ns
V
311