AT32UC3C264C Atmel Corporation, AT32UC3C264C Datasheet - Page 49
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT32UC3C264C
Manufacturer Part Number
AT32UC3C264C
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT32UC3A0128.pdf
(377 pages)
2.AT32UC3A0128.pdf
(159 pages)
3.AT32UC3C0128C.pdf
(1313 pages)
4.AT32UC3C0128C.pdf
(108 pages)
Specifications of AT32UC3C264C
Flash (kbytes)
64 Kbytes
Pin Count
64
Max. Operating Frequency
66 MHz
Cpu
32-bit AVR
Hardware Qtouch Acquisition
No
Max I/o Pins
45
Ext Interrupts
64
Usb Transceiver
1
Quadrature Decoder Channels
1
Usb Speed
Full Speed
Usb Interface
Device + OTG
Spi
5
Twi (i2c)
2
Uart
4
Can
2
Lin
4
Ssc
1
Ethernet
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
11
Adc Resolution (bits)
12
Adc Speed (ksps)
2000
Analog Comparators
2
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
12
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
20
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
3.0 to 3.6 or 4.5 to 5.5
Operating Voltage (vcc)
3.0 to 3.6 or 4.5 to 5.5
Fpu
Yes
Mpu / Mmu
Yes / No
Timers
3
Output Compare Channels
13
Input Capture Channels
6
Pwm Channels
14
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT32UC3C264C-A2UR
Manufacturer:
INTERSIL
Quantity:
1 670
Part Number:
AT32UC3C264C-U
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
6.2
6.2.1
6.2.2
32117CS–AVR-08/11
Startup Considerations
Starting of clocks
Fetching of initial instructions
This chapter summarizes the boot sequence of the AT32UC3C. The behavior after power-up is
controlled by the Power Manager. For specific details, refer to the Power Manager chapter.
At power-up, the BOD33 and the BOD18 are enabled. The device will be held in a reset state by
the power-up circuitry, until the VDDIN_33 (resp. VDDCORE) has reached the reset threshold of
the BOD33 (resp BOD18). Refer to the Electrical Characteristics for the BOD thresholds. Once
the power has stabilized, the device will use the System RC Oscillator (RCSYS, 115KHz typical
frequency) as clock source. The BOD18 and BOD33 are kept enabled or are disabled according
to the fuse settings (See the Fuse Setting section in the Flash Controller chapter).
On system start-up, the PLLs are disabled. All clocks to all modules are running. No clocks have
a divided frequency, all parts of the system receive a clock with the same frequency as the inter-
nal RC Oscillator.
After reset has been released, the AVR32UC CPU starts fetching instructions from the reset
address, which is 0x8000_0000. This address points to the first address in the internal Flash.
The internal Flash uses VDDIO voltage during read and write operations. It is recommended to
use the BOD33 to monitor this voltage and make sure the VDDIO is above the minimum level
(3.0V).
The code read from the internal Flash is free to configure the system to use for example the
PLLs, to divide the frequency of the clock routed to some of the peripherals, and to gate the
clocks to unused peripherals.
AT32UC3C
49