AT32UC3C164C Atmel Corporation, AT32UC3C164C Datasheet - Page 49

• Manufacturer Part Number: AT32UC3C164C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C164C

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 81
• Ext Interrupts: 100
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 20
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 19
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

6.2
6.2.1
6.2.2
32117CS–AVR-08/11
Startup Considerations
Starting of clocks
Fetching of initial instructions
This chapter summarizes the boot sequence of the AT32UC3C. The behavior after power-up is
controlled by the Power Manager. For specific details, refer to the Power Manager chapter.
At power-up, the BOD33 and the BOD18 are enabled. The device will be held in a reset state by
the power-up circuitry, until the VDDIN_33 (resp. VDDCORE) has reached the reset threshold of
the BOD33 (resp BOD18). Refer to the Electrical Characteristics for the BOD thresholds. Once
the power has stabilized, the device will use the System RC Oscillator (RCSYS, 115KHz typical
frequency) as clock source. The BOD18 and BOD33 are kept enabled or are disabled according
to the fuse settings (See the Fuse Setting section in the Flash Controller chapter).
On system start-up, the PLLs are disabled. All clocks to all modules are running. No clocks have
a divided frequency, all parts of the system receive a clock with the same frequency as the inter-
nal RC Oscillator.
After reset has been released, the AVR32UC CPU starts fetching instructions from the reset
address, which is 0x8000_0000. This address points to the first address in the internal Flash.
The internal Flash uses VDDIO voltage during read and write operations. It is recommended to
use the BOD33 to monitor this voltage and make sure the VDDIO is above the minimum level
(3.0V).
The code read from the internal Flash is free to configure the system to use for example the
PLLs, to divide the frequency of the clock routed to some of the peripherals, and to gate the
clocks to unused peripherals.
AT32UC3C
49