AT32UC3C164C Atmel Corporation, AT32UC3C164C Datasheet - Page 47

• Manufacturer Part Number: AT32UC3C164C
• Manufacturer: Atmel Corporation

Specifications of AT32UC3C164C

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 81
• Ext Interrupts: 100
• Usb Transceiver: 1
• Quadrature Decoder Channels: 2
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 7
• Twi (i2c): 3
• Uart: 5
• Can: 2
• Lin: 5
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 20
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6 or 4.5 to 5.5
• Operating Voltage (vcc): 3.0 to 3.6 or 4.5 to 5.5
• Fpu: Yes
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 22
• Input Capture Channels: 12
• Pwm Channels: 19
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

6.1.3.2
32117CS–AVR-08/11
3.3V Single Supply Mode
The 3.3V regulator is connected to the 5V source (VDDIN_5 pin) and its output feeds the USB
pads. If the USB is not used, the 3.3V regulator can be disabled through the VREG33CTL field
of the VREGCTRL SCIF register.
Figure 6-1 on page 47
I/O lines and analog blocks will be powered by the same power (VDDIN_5 = VDDIO1 = VDDIO2
= VDDIO3 = VDDANA).
Figure 6-1.
In 3.3V single supply mode, the VDDIN_5 and VDDIN_33 pins should be connected together
externally. The 1.8V internal regulator is connected to the 3.3 V source (VDDIN_5 pin) and its
output feeds VDDCORE.
The 3.3V regulator should be disabled once the circuit is running through the VREG33CTL field
of the VREGCTRL SCIF register.
Figure 6-2 on page 48
I/O lines and analog blocks will be powered by the same power (VDDIN_5 = VDDIN_33 =
VDDIO1 = VDDIO2 = VDDIO3 = VDDANA).
C
IN2
C
C
OUT2
OUT2
GNDCORE
VDDCORE
VDDIN_33
C
IN1
5V Single Power Supply mode
5.5V
C
C
4.5-
OUT1
OUT1
+
-
shows the power schematics to be used for 3.3V single supply mode. All
shows the power schematics to be used for 5V single supply mode. All
VDDIO1
VDDIO2
VDDIO3
BOD33
BOD18
BOD50
POR
3.3V
1.8V
Reg
Reg
VDDIN_5
VDDANA
Analog: ADC, AC, DAC, ...
SCIF, BOD,
Peripherals
Memories
RCSYS
CPU
PLL
GNDANA
AT32UC3C
GNDPLL
GNDIO1
GNDIO2
GNDIO3
47