PS21963-AT Mitsumi Electronics, Corp., PS21963-AT Datasheet
PS21963-AT
Available stocks
Related parts for PS21963-AT
PS21963-AT Summary of contents
Page 1
... Fault signaling : Corresponding fault (Lower-leg IGBT fault (Lower-side supply fault (LVIC temperature). • Input interface : 3V, 5V line (High Active). • UL Approved : Yellow Card No. E80276 APPLICATION AC100V~200V three-phase inverter drive for small power motor control. Fig. 1 PACKAGE OUTLINES (PS21963-T) 38 ±0.5 20×1.778(=35.56) 0.28 35 ± ...
Page 2
... Fig. 2 LONG TERMINAL TYPE PACKAGE OUTLINES (PS21963-AT) 38 ±0.5 20×1.778(=35.56) 0.28 35 ±0.3 ±0.2 1.778 17 QR Type name Code Lot No. 3 MIN 18 0.28 2.54 ±0.2 14×2.54 (=35.56) 0.5 HEAT SINK SIDE *) Two V terminals (9 & 16 pin) are connected inside DIPIPM, please connect either one to the 15V power supply GND outside and NC leave another one open ...
Page 3
... Fig. 4 BOTH SIDES ZIGZAG TERMINAL TYPE PACKAGE OUTLINES (PS21963-TW) 38 ±0.5 20×1.778(=35.56) 0.28 ±0.3 35 1.778 ±0. Type name Code Lot No. 3 MIN 18 0.28 ±0.25 2.54 14×2.54 (=35.56) 0.5 HEAT SINK SIDE *) Two V terminals (9 & 16 pin) are connected inside DIPIPM, please connect either one to the 15V power supply GND outside and NC leave another one open ...
Page 4
... FO Current sensing input voltage V SC PS21963-T/-AT/-CT/-TW Short Circuit Protective Function (SC protection is achieved by sensing the L-side DC-Bus current (through the external shunt resistor) after allowing a suitable filtering time (defined by the RC circuit). When the sensed shunt voltage exceeds the SC trip-level, all the L-side IGBTs are turned OFF and a fault signal (Fo) is output ...
Page 5
... T = 125° Inductive load (upper-lower arm 25° CES T = 125° PS21963-T/-AT/-CT/-TW TRANSFER-MOLD TYPE INSULATED TYPE Ratings 400 (Note 2) –20~+100 –40~+125 1500 Limits Min. Typ. Max. — — — — determined by the thickness and the thermal Limits Min ...
Page 6
... pulse width is 20µsec(min) for very short period less than 20µsec. O Condition Mounting screw : M3 Recommended : 0.69 N·m (Note 7) 4.6mm – + Heat sink side 6 PS21963-T/-AT/-CT/-TW TRANSFER-MOLD TYPE INSULATED TYPE Limits Min. Typ. Max. — — 2. — — 0.55 -W — ...
Page 7
... V WS IGBT4 Di4 LVIC U OUT V CC IGBT5 Di5 V OUT IGBT6 Di6 OUT Fo CIN V NO GND CIN 7 PS21963-T/-AT/-CT/-TW TRANSFER-MOLD TYPE INSULATED TYPE Limits Min. Typ. Max. 0 300 400 13.5 15.0 16.5 13.0 15.0 18.5 –1 — 1 1.5 — — — — 5kHz — — 5.0 PWM ...
Page 8
... Output current Ic Error output SET RESET reference voltage CR circuit time constant DELAY the circuits start to operate when next input is applied. Dr RESET SET PS21963-T/-AT/-CT/-TW TRANSFER-MOLD TYPE INSULATED TYPE RESET b6 b7 Mar. 2009 ...
Page 9
... Wiring inductance should be less than 10nH. Equivalent to the inductance of a copper pattern in dimension of width=3mm thickness=100µm, length=17mm N Shunt resistor Please make the GND wiring connection of shunt resistor to the V as close as possible. 9 PS21963-T/-AT/-CT/-TW TRANSFER-MOLD TYPE INSULATED TYPE 3.3kΩ ...
Page 10
... OUT F o GND CIN Long wiring here might cause SC level fluctuation and malfunction. 10 PS21963-T/-AT/-CT/-TW TRANSFER-MOLD TYPE INSULATED TYPE Bootstrap negative electrodes should be connected terminals directly and separated from the main output wires Long wiring here might Long wiring here might cause short-circuit ...