ISP1104 NXP Semiconductors, ISP1104 Datasheet
ISP1104
Available stocks
Related parts for ISP1104
ISP1104 Summary of contents
Page 1
... Rev. 02 — 14 October 2003 1. General description The ISP1104 Universal Serial Bus (USB) transceiver is compliant with the Universal Serial Bus Specification Rev. 2.0 . The ISP1104 can transmit and receive USB data at full-speed (12 Mbit/s). It allows single and differential input modes selectable by a MODE input. ...
Page 2
... V V CC(I/O) REGULATOR VBUSDET SOFTCON OE MODE (1) VMO/FSE0 LEVEL SHIFTER (1) VPO/VO ISP1104 SUSPND RCV VP VM Rev. 02 — 14 October 2003 ISP1104 Advanced USB transceiver Version SOT639-2 3 0.65 mm VOLTAGE V CC(5.0) V reg(3.3) V pu(3. (1%) GND 004aaa035 Section 7.2. ...
Page 3
... D receiver output (CMOS level with respect to V conditions and speed of connected device; driven HIGH when no supply voltage is connected reg(3.3) output pad; push pull output drive; CMOS Rev. 02 — 14 October 2003 ISP1104 Advanced USB transceiver VPO/VO ...
Page 4
... CMOS exposed - ground supply; down bonded to the exposed die pad die pad (heatsink connected to the PCB ground Rev. 02 — 14 October 2003 ISP1104 Advanced USB transceiver CC(I/ HIGH CC(I/O) Table 4 and Table 5 and must never exceed the V reg(3.3) > ...
Page 5
... L differential logic 0 H illegal state Receiving function (pin RCV L H [2] RCV* CC(5.0) Rev. 02 — 14 October 2003 ISP1104 Advanced USB transceiver VP/VM Function active normal driving (differential receiver active) active receiving active driving during ‘suspend’ (differential receiver inactive) active ...
Page 6
... V to 3.6 V), depending on the supply voltage of the external circuit. Disable mode — V the internal circuits of the ISP1104 ensure that the D and D pins are in three-state and the power consumption drops to the low-power (suspended) state level. Some hysteresis is built into the detection of V Sharing mode — ...
Page 7
... ESD protection. The 12 kV measurement is limited by the test equipment. Capacitors of 4.7 F connected from V are required to achieve this 12 kV ESD protection (see The ISP1104 can withstand 12 kV using the Human Body Model and 5 kV using the Contact Discharge Method as specified in IEC 61000-4-2 . HIGH VOLTAGE DC SOURCE Fig 3 ...
Page 8
... Mbit/s idle: V > 2 < 0 SE0: V < 0 < 0 idle, SE0 or suspend SUSPND = not connected CC CC(I/O) not connected CC(5.0) Rev. 02 — 14 October 2003 ISP1104 Advanced USB transceiver Min Max 0.5 6.0 0.5 4.6 0 0.5 CC(I/O) - 100 [1][2] 12000 12000 2000 2000 40 125 and V ...
Page 9
... unless otherwise specified. amb Conditions Min - 0. 100 100 CC(I/ CC(I/O) [1] 1 pin to GND - - 1 100 Rev. 02 — 14 October 2003 ISP1104 Advanced USB transceiver Min Typ Max - - 3.6 4 0.5 1 0.45 - Typ Max - 0.3V CC(I/ CC(I/O) - 0.15 - 0.4 0. ...
Page 10
... 100 unless otherwise specified. amb Conditions V V I(D ) I(D ) includes V range 1 +3 GND L Rev. 02 — 14 October 2003 ISP1104 Advanced USB transceiver Typ Max - - - - - 0 0. 0. ...
Page 11
... Figure 5 LOW-to-HIGH; see Figure 5 HIGH-to-LOW; see Figure 5 HIGH-to-OFF; see Figure 6 LOW-to-OFF; see Figure 6 Rev. 02 — 14 October 2003 ISP1104 Advanced USB transceiver Min Typ Max - - 20 [ ...
Page 12
... Fig 5. Timing of VPO/VO and VMO/FSE0 to D and D . 2.0 V differential V CRS 0.9 V data lines 0 PHZ t PLZ V OH logic output V OL MGS966 Fig 7. Timing of D and D to RCV, VP and VM. Rev. 02 — 14 October 2003 ISP1104 Advanced USB transceiver Figure 8; unless otherwise Min Typ Max - - ...
Page 13
... L test point 33 D.U.T. and t . PZH PHZ for t and t . reg(3.3) PZL PLZ test point D.U.T. Rev. 02 — 14 October 2003 ISP1104 Advanced USB transceiver test point 500 MBL142 25 pF MGS968 © Koninklijke Philips Electronics N.V. 2003. All rights reserved ...
Page 14
... 2.5 scale 0.38 0.38 3.1 1.45 3.1 1.45 0.5 0.32 0.32 2.9 1.35 2.9 1.35 REFERENCES JEDEC JEITA MO-217 Rev. 02 — 14 October 2003 ISP1104 Advanced USB transceiver ...
Page 15
... Philips Semiconductors 15. Packaging The ISP1104W (HBCC16 package) is delivered on a type A carrier tape, see Figure The reel diameter is 330 mm. The reel is made of polystyrene (PS) and is not designed for use in a baking process. The cumulative tolerance of 10 successive sprocket holes is 0.02 mm. The camber must not exceed 100 mm. ...
Page 16
... 0.05 = 260 C amb(max) case(max) Rev. 02 — 14 October 2003 ISP1104 Advanced USB transceiver Stencil mask All dimensions in mm Solder land 0.05 Solder resist Solder stencil 0.05 For exact dimensions see package outline drawing (SOT639-2) 0.05 0.05 0 Stencil print thickness: 0.1 to 0.12 mm 004aaa123 = 255 C. © ...
Page 17
... also, changed the description CC(dis) CC-I/O(dis) 13: removed Z , and also the relevant (old) table note 3. DRV2 Rev. 02 — 14 October 2003 ISP1104 Advanced USB transceiver © Koninklijke Philips Electronics N.V. 2003. All rights reserved ...
Page 18
... Rev. 02 — 14 October 2003 ISP1104 Advanced USB transceiver Fax: + 24825 © Koninklijke Philips Electronics N.V. 2003. All rights reserved ...
Page 19
... No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 14 October 2003 Document order number: 9397 750 11229 ISP1104 Advanced USB transceiver ...