LC72322R Sanyo Semiconductor Corporation, LC72322R Datasheet
LC72322R
Available stocks
Related parts for LC72322R
LC72322R Summary of contents
Page 1
... The LC72322R and LC72323R are single-chip microcontrollers for use in electronic tuning applications. These ICs include on chip both LCD drivers and a PLL circuit that can operate 150 MHz. The LC72322R and LC72323R feature that these ICs are reversed pin- assignment versions of LC72322 and LC72323 respectively and have the equal functions and specifications to theirs respectively ...
Page 2
... Pin Assignment LC72322R, 72323R No. 5378-2/13 ...
Page 3
... Block Diagram LC72322R, 72323R No. 5378-3/13 ...
Page 4
... Input amplitude Input voltage range LC72322R, 72323R = Symbol Conditions V max HOLD, INT, RES, ADI, SNS, and the G port Inputs other than port OUT V 2 Outputs other than V ...
Page 5
... Current drain LC72322R, 72323R Conditions min LCTR (period), RES, INT, PE1, PE3 0.1 V SNS INT, HOLD, RES, ADI, SNS, and G port 5 and F ports: E and F ports with outputs off, A port with ...
Page 6
... Test Circuits Note PF, PH, and PI are all open. However, PE and PF are specified as output. Figure 1 I Note PI S4, COM1, and COM2 are all open. LC72322R, 72323R HOLD Mode DD DD Figure BACK UP Mode DD No. 5378-6/13 ...
Page 7
... RES pin is low. PF3 54 In BACKUP mode these pins go to the input mode with input disabled. PG0 59 PG1 60 Dedicated input ports PG2 61 Input through these pins is disabled in BACKUP mode. PG3 62 LC72322R, 72323R Functions I/O Input Output I/O Input I/O circuit type Continued on next page. No. 5378-7/13 ...
Page 8
... PH1 56 And, PH2 and PH3 can also be used for DAC1 and DAC2 PH2/DAC output ports respectively. (*: DAC is contained in LC72322R PH3/DAC only.) These ports go to the high impedance state during a reset, i.e., when the RES pin is low, and in BACKUP mode. ...
Page 9
... Crystal oscillator connections XIN 64 (4.5 MHz) XOUT 65 A feedback resistor is built in. TEST1 66 LSI test pins. These pins must be connected to V TEST2 Power supply LC72322R, 72323R Functions I/O Input Input ) for a data DD Input Output Input Input Input Input Output . — SS — I/O circuit type ...
Page 10
... The LC72P321R is used for OTP. • The LC72EV321 is used as the evaluation chip. • A total debugging system is available in which the TB-72EV32 evaluation chip board and the RE32 multifunction emulator are controlled by a personal computer. LC72322R, 72323R Selections WDT included No WDT Pull-down resistors included No pull-down resistors 2.67 µ ...
Page 11
... LC72322R, 72323R Instruction Table Abbreviations: ADDR: Program memory address [12 bits] b: Borrow B: Bank number [2 bits] C: Carry DH: Data memory address high (row address) [2 bits] DL: Data memory address low (column address) [4 bits] I: Immediate data [4 bits] M: Data memory address N: Bit position [4 bits] Pn: Port number [4 bits] ...
Page 12
... SS N Set status register RS N Reset status register TST N Test status register true TSF N Test status register false BANK B Select bank LC72322R, 72323R Operation D15 ( ( ...
Page 13
... Load M to D/A registers NOP No operation Note: * DAC is contained in LC72322R only. No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. ...