TDA3856 NXP Semiconductors, TDA3856 Datasheet
TDA3856
Available stocks
Related parts for TDA3856
TDA3856 Summary of contents
Page 1
... DATA SHEET TDA3856 Quasi-split sound processor for all standards Product specification File under Integrated Circuits, IC02 INTEGRATED CIRCUITS June 1994 ...
Page 2
... AM ORDERING INFORMATION EXTENDED TYPE NUMBER PINS TDA3856 TDA3856T Note 1. SOT234-1; 1996 November 28. 2. SOT137-1; 1996 November 28. June 1994 PARAMETER PIN POSITION 24 shrink DIL Product specification MIN. TYP. 4 0.6 0 PACKAGE MATERIAL plastic plastic TDA3856 MAX. UNIT 8 100 CODE (1) SOT234 (2) SOT137 ...
Page 3
... Philips Semiconductors Quasi-split sound processor for all standards June 1994 Fig.1 Block diagram (B/G and L). 3 Product specification TDA3856 ...
Page 4
... FM2 (5.74 MHz) GND 20 ground ( supply voltage charge capacitor for reference voltage REF FMIF1 23 IF difference input 1 for B/G standard (38.9 MHz) FMIF2 24 IF difference input 2 for B/G standard (38.9 MHz) June 1994 DESCRIPTION 4 Product specification TDA3856 Fig.2 Pin configuration. ...
Page 5
... AMF2’ (weighted S/N) must kHz sine wave modulation of the B/W-signal. Signal-to-noise ratios are measured with kHz deviation and kHz; with a deviation of 30 kHz the mod S/N ratio is deteriorated by 4.5 dB. 5 Product specification TDA3856 ...
Page 6
... MHz mV; vision to sound carrier ratios are VC/SC1 = 13 dB and i VC CONDITIONS pin 5 connected pin 5 open-circuit pin 5 connected or alternative measure GND pin 5 connected LOW set internally note 1 6 Product specification TDA3856 MIN. MAX. UNIT 8 650 mW 25 +150 C 0 +70 C 500 V 400 ...
Page 7
... Figs 3 and note 2 1st/2nd harmonic (38.9/77.8 MHz emitter current LC-circuit at pin 12, 13 1.5 adjusted to minimum video content at pin signal 200 450 only 5.74 MHz channel 0 Product specification TDA3856 TYP. MAX. UNIT 1.75 V 100 mV 70 100 V 70 100 V 2 MHz 270 0.247 H ...
Page 8
... Fig.4 CCIR468-3 8 Product specification MIN. TYP kHz, deviation i IF (RMS) mod 100 1.8 0.84 0.95 75 100 1.8 2.1 0.5 1. 100 (RMS) 530 600 75 100 1.8 2 100 2 TDA3856 MAX. UNIT 130 2 kHz dB V 675 mV 130 1 2 kHz ...
Page 9
... MHz 5.742 MHz 5.742 MHz 5.742 MHz 5.742 MHz 200 mV; R(p- out R = 470 12-13 set to a value to achieve V 3 B)/ signal at sync signal with 100% picture modulation). 9 Product specification MIN. TYP (instead of LC circuit (pins 12-13). o (RMS) TDA3856 MAX. UNIT ...
Page 10
... Philips Semiconductors Quasi-split sound processor for all standards Fig.3 Test and application circuit for standards B/G and L (for application SAW-filters must be used). June 1994 10 Product specification TDA3856 ...
Page 11
... Philips Semiconductors Quasi-split sound processor for all standards Fig.4 Total harmonic distortion (THD) as function of audio frequency at AM standard (V (1) simple resonant circuit (2) resonant circuit with (see Fig.3) s Fig.5 Frequency response of the 38.9 MHz reference circuit. June 1994 11 Product specification TDA3856 = 0). 5 ...
Page 12
... Philips Semiconductors Quasi-split sound processor for all standards APPLICATION INFORMATION June 1994 Fig.6 Internal circuits (continued in Fig.7). 12 Product specification TDA3856 ...
Page 13
... Philips Semiconductors Quasi-split sound processor for all standards June 1994 Fig.7 Internal circuits (continued from Fig.6). 13 Product specification TDA3856 ...
Page 14
... VERSION IEC SOT234-1 June 1994 scale (1) ( 1.3 0.53 0.32 22.3 9.1 0.8 0.40 0.23 21.4 8.7 REFERENCES JEDEC EIAJ 14 Product specification 3.2 10.7 12.2 1.778 10.16 2.8 10.2 10.5 EUROPEAN PROJECTION TDA3856 SOT234-1 ( max. 0.18 1.6 ISSUE DATE 92-11-17 95-02-04 ...
Page 15
... REFERENCES JEDEC EIAJ MS-013AD detail 1.1 1.1 0.25 0.25 1.4 0.4 1.0 0.043 0.043 0.055 0.01 0.01 0.016 0.039 EUROPEAN PROJECTION Product specification TDA3856 SOT137 ( 0.9 0.1 0 0.035 0.004 0.016 ISSUE DATE 95-01-24 97-05-22 ...
Page 16
... Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 16 Product specification TDA3856 ...
Page 17
... These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. June 1994 17 Product specification TDA3856 ...