LME49811TB/NOPB National Semiconductor, LME49811TB/NOPB Datasheet - Page 12

• Manufacturer Part Number: LME49811TB/NOPB
• Description: IC AMP AUDIO PWR 500W TO247-15
• Manufacturer: National Semiconductor
• Type: Class ABr

Specifications of LME49811TB/NOPB

• Output Type: 1-Channel (Mono)
• Max Output Power X Channels @ Load: 500W x 1 @ 8 Ohm
• Voltage - Supply: 40 V ~ 200 V, ±20 V ~ 100 V
• Features: Shutdown, Thermal Protection
• Mounting Type: Through Hole
• Package / Case: TO-247-15 (Bent and Staggered Leads)
• Amplifier Class: AB
• No. Of Channels: 1
• Supply Voltage Range: ± 20V To ± 100V
• Load Impedance: 8ohm
• Operating Temperature Range: -40°C To +85°C
• Amplifier Case Style: TO-247
• No. Of Pins: 15
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: LME49811TB

www.national.com
With large values of R
outputs when the inputs are left floating. Decreasing the value
of R
If the value of R
to increase in order to maintain the same -3dB frequency re-
sponse.
COMPENSATION CAPACITOR
The compensation capacitor (C
external components in value, placement and type. The ca-
pacitor should be placed close to the LME49811 and a silver
mica type will give good performance. The value of the ca-
pacitor will affect slew rate and stability. The highest slew rate
is possible while also maintaining stability through out the
power and frequency range of operation results in the best
audio performance. The value shown in Figure 1 should be
considered a starting value with optimization done on the
bench and in listening testing.
SUPPLY BYPASSING
The LME49811 has excellent power supply rejection and
does not require a regulated supply. However, to eliminate
possible oscillations all op amps and power op amps should
have their supply leads bypassed with low-inductance capac-
itors having short leads and located close to the package
terminals. Inadequate power supply bypassing will manifest
itself by a low frequency oscillation known as “motorboating”
or by high frequency instabilities. These instabilities can be
eliminated through multiple bypassing utilizing a large elec-
trolytic capacitor (10μF or larger) which is used to absorb low
frequency variations and a small ceramic capacitor (0.1μF) to
prevent any high frequency feedback through the power sup-
ply lines. If adequate bypassing is not provided the current in
the supply leads which is a rectified component of the load
current may be fed back into internal circuitry. This signal
causes low distortion at high frequencies requiring that the
supplies be bypassed at the package terminals with an elec-
trolytic capacitor of 470μF or more.
OUTPUT STAGE USING BIPOLAR TRANSISTORS
With a properly designed output stage and supply voltage of
±100V, an output power up to 500W can be generated at
0.05% THD+N into an 8Ω speaker load. With an output cur-
rent of several amperes, the output transistors need substan-
tial base current drive because power transistors usually have
quite low current gain—typical h
current gain, audio amplifiers commonly use Darlington style
devices or additional driver stages. Power transistors should
be mounted together with the V
same heat sink to avoid thermal run away. Please see the
section Biasing Technique and Avoiding Thermal Run-
away for additional information.
BIASING TECHNIQUES AND AVOIDING THERMAL
RUNAWAY
A class AB amplifier has some amount of distortion called
Crossover distortion. To effectively minimize the crossover
distortion from the output, a V
stead of two biasing diodes. A V
of a bipolar transistor (Q
(R
series with R
B1
IN
and R
or not letting the inputs float will remove the oscillations.
B2
, see Figure 1). A trim pot can also be added in
B1
IN
for optional bias adjustment. A properly de-
is decreased then the value of C
IN
MULT
oscillations may be observed on the
, see Figure 1) and two resistors
BE
BE
fe
BE
C
) is one of the most critical
of 50 or so. To increase the
multiplier normally consists
multiplier may be used in-
multiplier transistor on the
IN
will need
12
signed output stage, combine with a V
inate the trim pot and virtually eliminate crossover distortion.
The V
stage) can be set by following formula:
When using a bipolar output stage with the LME49811 (as in
Figure 1), the designer must beware of thermal runaway.
Thermal runaway is a result of the temperature dependence
of V
increases, V
a bipolar transistor heats up the transistor, which lowers the
V
peats. If the system is not designed properly this positive
feedback mechanism can destroy the bipolar transistors used
in the output stage. One of the recommended methods of
preventing thermal runaway is to use the same heat sink on
the bipolar output stage transistor together with V
transistor. When the V
same heat sink as the bipolar output stage transistors, it tem-
perature will track that of the output transistors. Its V
dependent upon temperature as well, and so it will draw more
current as the output transistors heat up, reducing the bias
voltage to compensate. This will limit the base current into the
output transistors, which counteracts thermal runaway. An-
other widely popular method of preventing thermal runaway
is to use low value emitter degeneration resistors (R
R
creases, which decreases the voltage across the base and
emitter. This mechanism helps to limit the current and coun-
teracts thermal runaway.
LAYOUT CONSIDERATION AND AVOIDING GROUND
LOOPS
A proper layout is virtually essential for a high performance
audio amplifier. It is very important to return the load ground,
supply grounds of output transistors, and the low level (feed-
back and input) grounds to the circuit board common ground
point through separate paths. When ground is routed in this
fashion, it is called a star ground or a single point ground. It
is advisable to keep the supply decoupling capacitors of
0.1μF close as possible to LME49811 to reduce the effects of
PCB trace resistance and inductance. Following the general
rules will optimize the PCB layout and avoid ground loops
problems:
a) Make use of symmetrical placement of components.
b) Make high current traces, such as output path traces, as
wide as possible to accommodate output stage current re-
quirement.
c) To reduce the PCB trace resistance and inductance, same
ground returns paths should be as short as possible. If pos-
sible, make the output traces short and equal in length.
d) To reduce the PCB trace resistance and inductance,
ground returns paths should be as short as possible.
e) If possible, star ground or a single point ground should be
observed. Advanced planning before starting the PCB can
improve audio performance.
BE
E2
. This in turn increases the current gain, and the cycle re-
). As current increases, the voltage at the emitter also in-
BE
CE
(an inherent property of the transistor). As temperature
voltage of Q
BE
V
BIAS
decreases. In practice, current flowing through
= V
BE
BE
MULT
(1+R
multiplier transistor is mounted to the
(also called BIAS of the output
B2
/R
B1
)
BE
(V)
multiplier, can elim-
BE
multiplier
E1
BE
and
(6)
is