SC28L198A1A,529 NXP Semiconductors, SC28L198A1A,529 Datasheet - Page 25
![IC UART OCTAL SOT189-3](/photos/6/98/69866/568-84-plcc_sot189-2_sml.jpg)
SC28L198A1A,529
Manufacturer Part Number
SC28L198A1A,529
Description
IC UART OCTAL SOT189-3
Manufacturer
NXP Semiconductors
Datasheet
1.SC28L198A1BE557.pdf
(57 pages)
Specifications of SC28L198A1A,529
Features
False-start Bit Detection
Number Of Channels
8
Fifo's
16 Byte
Voltage - Supply
3.3V, 5V
With Auto Flow Control
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Package / Case
84-LCC (J-Lead)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
935261323529
SC28L198A1A-S
SC28L198A1A-S
SC28L198A1A-S
SC28L198A1A-S
Philips Semiconductors
meets or exceeds the value; it is reset when the fill level is less.
See the description of the MR2 register.
Note: This bit must be at a one (1) for the receiver to enter the
arbitration process. It is the fact that this bit is zero (0) when the
RxFIFO is empty that stops an empty FIFO from entering the
interrupt arbitration. Also note that the meaning if this bit is not quite
the same as the similar bit in the status register (SR).
ISR[0] – Transmitter Ready
The general function of this bit is to indicate that the TxFIFO has an
at least one empty space for data. The particular meaning of the bit
is controlled by MR0[5:4] indicates the TxFIFO may be loaded with
one or more characters. If MR0[5:4] = 00 (the default condition) this
bit will not set until the TxFIFO is empty – sixteen bytes available. If
Table 12. IMR – Interrupt Mask Register
The programming of this register selects which bits in the ISR cause
an interrupt output. If a bit in the ISR is a ’1’ and the corresponding
bit in the IMR is a ’1’, the interrupt source is presented to the internal
interrupt arbitration circuits, eventually resulting in the IRQN output
being asserted (low). If the corresponding bit in the IMR is a zero,
the state of the bit in the ISR has no affect on the IRQN output.
IMR[7] – Controls if a change of state in the inputs equipped with
input change detectors will cause an interrupt.
IMR[6] – Controls the generation of an interrupt by the watch-dog
timer event. If set, a count of 64 idle bit times in the receiver will
begin interrupt arbitration.
Table 13. RxFIFO Receiver FIFO
The FIFO for the receiver is 11 bits wide and 16 ”words” deep. The
status of each byte received is stored with that byte and is moved
along with the byte as the characters are read from the FIFO. The
upper three bits are presented in the STATUS register and they
change in the status register each time a data byte is read from the
FIFO. Therefor the status register should be read BEFORE the byte
is read from the RxFIFO if one wishes to ascertain the quality of the
byte
The forgoing applies to the ”character error” mode of status
reporting. See MR1[5] and ”RxFIFO Status” descriptions for ”block
error” status reporting. Briefly ”Block Error” gives the accumulated
error of all bytes received in the RxFIFO since the last “Reset Error”
command was issued. (CR = x’04)
Table 14. TxFIFO – Transmitter FIFO
The FIFO for the transmitter is 8 bits wide by 16 bytes deep. For
character lengths less than 8 bits the upper bits will be ignored by
the transmitter state machine and thus are effectively discarded.
2006 Aug 10
Bit 7
I/O Port change
of state
Bit[10]
Break
Received
Status
Bits 7:0
8 data bits. MSBs set to 0 for 7, 6, 5 bit data
Octal UART for 3.3 V and 5 V supply voltage
Bit[9]
Framing
Error Sta-
tus
Bit 6
Receiver Watch-dog
Time–out
Bit[8]
Parity
Error Sta-
tus
Bits [7:0]
8 data bits
MSBs =0 for 7,6,5 bit
data
Bit 5
Address recogni-
tion event
Bit 4
Xon/off event
25
the fill level of the TxFIFO is below the trigger level programmed by
the TxINT field of the Mode Register 0, this bit will be set. A one in
this position indicates that at least one character can be sent to the
TxFIFO. It is turned off as the TxFIFO is filled above the level
programmed by MR0[5:4. This bit turns on as the FIFO empties; the
RxFIFO bit turns on as the FIFO fills. This often a point of confusion
in programming interrupt functions for the receiver and transmitter
FIFOs.
Note: This bit must be at a one (1) for the transmitter to enter the
arbitration process. It is the fact that this bit is zero (0) when the
RxFIFO is full that stops a full FIFO from entering the interrupt
arbitration. Also note that the meaning if this bit is not quite the
same as the similar bit in the status register (SR).
IMR[5] – Enables the generation of an interrupt in response to
changes in the Address Recognition circuitry of the Special Mode
(multi-drop or wake–up mode).
IMR[4] – Enables the generation of an interrupt in response to
recognition of an in–band flow control character.
IMR[3] – Reserved
IMR[2] – Enables the generation of an interrupt when a Break
condition has been detected by the channel receiver.
IMR[1] – Enables the generation of an interrupt when servicing for
the RxFIFO is desired.
IMR[0] – Enables the generation of an interrupt when servicing for
the TxFIFO is desired.
Table 15. BCRBRK – Bidding Control Register –
This register provides the 3 MSBs of the Interrupt Arbitration number
for a break change interrupt.
Table 16. BCRCOS – Bidding Control Register –
This register provides the 3 MSBs of the Interrupt Arbitration number
for a Change of State, COS, interrupt.
Table 17. BCRx – Bidding Control Register – Xon
This register provides the 3 MSBs of the Interrupt Arbitration number
for an Xon/Xoff interrupt.
Bits 7:3
Reserved
Bits 7:3
Reserved
Read as x’0
Bits 7:3
Reserved
Bit 3
Set to 0
Break Change
Change of State
Bit 2
Break State
Change of
Bits 2:0
MSB of break change interrupt bid
Bits 2:0
MSB of a COS interrupt bid
Bits 2:0
MSB of an Xon/Xoff interrupt bid
Bit 1
RxRDY inter-
rupt
SC28L198
Product data sheet
Bit 0
TxRDY inter-
rupt