SC16C852VIET,118 NXP Semiconductors, SC16C852VIET,118 Datasheet - Page 21

• Manufacturer Part Number: SC16C852VIET,118
• Description: IC UART DUAL W/FIFO 36TFBGA
• Manufacturer: NXP Semiconductors

Specifications of SC16C852VIET,118

• Features: Programmable
• Number Of Channels: 2, DUART
• Fifo's: 128 Byte
• Protocol: RS485
• Voltage - Supply: 1.8V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Package / Case: 36-TFBGA
• Transmitter And Receiver Fifo Counter: Yes
• Data Rate: 5Mbps
• Mounting: Surface Mount
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

NXP Semiconductors
SC16C852_1
Product data sheet
6.14.3.1 Normal Multi-drop mode
6.14.1 Auto RS-485 RTS control
6.14.2 RS-485 RTS inversion
6.14.3 Auto 9-bit mode (RS-485)
6.14 RS-485 features
Normally the RTSA/RTSB pin is controlled by MCR bit 1, or if hardware flow control is
enabled, the logic state of the RTSx pin is controlled by the hardware flow control circuitry.
AFCR2 register bit 4 will take the precedence over the other two modes; once this bit is
set, the transmitter will control the state of the RTSx pin. The transmitter automatically
asserts the RTSx pin (logic 0) once the host writes data to the transmit FIFO, and
de-asserts RTSx pin (logic 1) once the last bit of the data has been transmitted.
To use the auto RS-485 RTS mode the software would have to disable the hardware
flow control function.
AFCR2[5] reverses the polarity of the RTSx pin if the UART is in auto RS-485 RTS mode.
When the transmitter has data to be sent it will de-asserts the RTSx pin (logic 1), and
when the last bit of the data has been sent out the transmitter asserts the RTSx pin
(logic 0).
AFCR2[0] is used to enable the 9-bit mode (Multi-drop or RS-485 mode). In this mode of
operation, a ‘master’ station transmits an address character followed by data characters
for the addressed ‘slave’ stations. The slave stations examine the received data and
interrupt the controller if the received character is an address character (parity bit = 1).
To use the automatic 9-bit mode, the software would have to disable the hardware and
software flow control functions.
The 9-bit Mode in AFCR2[0] is enabled, but not Special Character Detect (EFR[5]). The
receiver is set to Force Parity 0 (LCR[5:3] = 111) in order to detect address bytes.
With the receiver initially disabled, it ignores all the data bytes (parity bit = 0) until an
address byte is received (parity bit = 1). This address byte will cause the UART to set the
parity error. The UART will generate a line status interrupt (IER bit 2 must be set to ‘1’ at
this time), and at the same time puts this address byte in the RX FIFO. After the controller
examines the byte it must make a decision whether or not to enable the receiver; it should
enable the receiver if the address byte addresses its ID address, and must not enable the
receiver if the address byte does not address its ID address.
If the controller enables the receiver, the receiver will receive the subsequent data until
being disabled by the controller after the controller has received a complete message from
the ‘master’ station. If the controller does not disable the receiver after receiving a
message from the ‘master’ station, the receiver will generate a parity error upon receiving
another address byte. The controller then determines if the address byte addresses its ID
address, if it is not, the controller then can disable the receiver. If the address byte
addresses the ‘slave’ ID address, the controller takes no further action, and the receiver
will receive the subsequent data.
Rev. 01 — 31 August 2009
Dual UART with 128-byte FIFOs and IrDA encoder/decoder
SC16C852
© NXP B.V. 2009. All rights reserved.
21 of 60