SC16C652BIB48,128 NXP Semiconductors, SC16C652BIB48,128 Datasheet - Page 25
![IC ENCODER/DECODER IRDA 48LQFP](/photos/6/64/66484/568-48-lqfp_sot313-2_sml.jpg)
SC16C652BIB48,128
Manufacturer Part Number
SC16C652BIB48,128
Description
IC ENCODER/DECODER IRDA 48LQFP
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C652BIB48128.pdf
(43 pages)
Specifications of SC16C652BIB48,128
Features
2 Channels
Number Of Channels
2, DUART
Fifo's
32 Byte
Voltage - Supply
2.5V, 3.3V, 5V
With Auto Flow Control
Yes
With Irda Encoder/decoder
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Package / Case
48-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
935274409128
SC16C652BIB48-F
SC16C652BIB48-F
SC16C652BIB48-F
SC16C652BIB48-F
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SC16C652BIB48,128
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Philips Semiconductors
SC16C652B_4
Product data sheet
7.10 Enhanced Feature Register (EFR)
Enhanced features are enabled or disabled using this register.
Bits 0 through 4 provide single or dual character software flow control selection. When the
Xon1 and Xon2 and/or Xoff1 and Xoff2 modes are selected, the double 8-bit words are
concatenated into two sequential numbers.
Table 23:
Bit
7
6
5
4
3:0
Symbol
EFR[7]
EFR[6]
EFR[5]
EFR[4]
EFR[3:0] Cont-3:0 Tx, Rx control. Logic 0 or cleared is the default condition.
Enhanced Feature Register bits description
Description
Automatic CTS flow control.
Automatic RTS flow control. Automatic RTS may be used for hardware flow
control by enabling EFR[6]. When Auto-RTS is selected, an interrupt will be
generated when the receive FIFO is filled to the programmed trigger level and
RTS will go to a logic 1 at the next trigger level. RTS will return to a logic 0 when
data is unloaded below the next lower trigger level (programmed trigger level 1).
The state of this register bit changes with the status of the hardware flow
control. RTS functions normally when hardware flow control is disabled.
logic
Special Character Detect.
Enhanced function control bit. The content of IER[7:4], ISR[5:4], FCR[5:4], and
MCR[7:5] can be modified and latched. After modifying any bits in the enhanced
registers, EFR[4] can be set to a logic 0 to latch the new values. This feature
prevents existing software from altering or overwriting the SC16C652B
enhanced functions.
Combinations of software flow control can be selected by programming these
bits. See
logic 0 = automatic CTS flow control is disabled (normal default condition)
logic 1 = enable automatic CTS flow control. Transmission will stop when
CTS goes to a logical 1. Transmission will resume when the CTS pin returns
to a logical 0.
0 = automatic RTS flow control is disabled (normal default condition)
logic 1 = enable automatic RTS flow control
logic 0 = special character detect disabled (normal default condition)
logic 1 = special character detect enabled. The SC16C652B compares each
incoming receive character with Xoff2 data. If a match exists, the received
data will be transferred to FIFO and ISR[4] will be set to indicate detection of
special character. Bit-0 in the X-registers corresponds with the LSB bit for the
receive character. When this feature is enabled, the normal software flow
control must be disabled (EFR[3:0] must be set to a logic 0).
logic 0 = disable/latch enhanced features. IER[7:4], ISR[5:4], FCR[5:4], and
MCR[7:5] are saved to retain the user settings, then IER[7:4] ISR[5:4],
FCR[5:4], and MCR[7:5] are set to a logic 0 to be compatible with SC16C554
mode. (Normal default condition.)
logic 1 = enables the enhanced functions. When this bit is set to a logic 1, all
enhanced features of the SC16C652B are enabled and user settings stored
during a reset will be restored.
Rev. 04 — 1 September 2005
Table
Dual UART with 32-byte FIFOs and IrDA encoder/decoder
24.
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
SC16C652B
25 of 43