PBL38640/2QNT Infineon Technologies, PBL38640/2QNT Datasheet - Page 38
![no-image](/images/manufacturer_photos/0/3/327/infineon_technologies_sml.jpg)
PBL38640/2QNT
Manufacturer Part Number
PBL38640/2QNT
Description
IC LINE INTERFACE SLIC PLCC-28
Manufacturer
Infineon Technologies
Series
FlexiSLIC™r
Datasheet
1.PBL386402QNA.pdf
(51 pages)
Specifications of PBL38640/2QNT
Function
Subscriber Line Interface Concept (SLIC)
Number Of Circuits
1
Voltage - Supply
5V
Current - Supply
2.8mA
Power (watts)
730mW
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
28-PLCC
Includes
Current Feeding, Ground Key Detector, Ring Relay Driver
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Interface
-
Other names
PBL38640/2QNTT
SP000007901
SP000007901
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PBL38640/2QNT
Manufacturer:
Infineon Technologies
Quantity:
10 000
components have an influence on the power supply rejection ratio (PSRR) from
the two-wire side at sub audio frequencies.At these frequencies
transversal to longitudinal balance in the SLIC.
C
table below, for the chosen value of
Table 9
Symbol
R
R
C
T-L bal. @
200 Hz
C
6
The PBL 38640/2 SLIC emulates resistive loop feed, programmable between 2x50
and 2x900 , with adjustable current limitation. In the current limited region the loop
current has a slight slope corresponding to 2x30 , see
The open loop voltage measured between the TIPX and RINGX terminals tracks the
battery voltage
programmable with a resistor
ground. Please refer to
programmed signal overhead voltage
open loop conditions according to
V
Refer to
changed when line corrent is approaching open loop conditions. To ensure maximum
open loop voltage, even with a leaking telephone line, this occurs at a line current of
approximately 6 mA. When the overhead voltage has changed, the line voltage is kept
nearly constant with a steep slope corresponding to 2x25
The virtual battery overhead,
voltage and the crossing point of all possible resistive feeding slopes, see
reference J. The virtual battery overhead is a theoretical constant needed to be able to
calculate the feeding characteristics.
Data Sheet
Feed
SG
TR
LP
LP
HP
. The typical value of the transversal to longitudinal balance at 200 Hz is given in the
(at
I
L
= 0 mA) = |
Table 10
Battery Feed
Feeding Setup
2 x 50
0
150
-46
47
V
BAT
for the typical value of
V
BAT
. The signalling headroom, or overhead voltage
Chapter
| -
V
OH
V
2 x 200
60.4
100
-46
150
R
OHvirt
OV
6.2. The battery voltage overhead,
connected between terminal POV on the SLIC and
C
, is defined as the difference between the battery
LP
V
.
TRO
Value
38
.
2 x 400
147
47
-43
150
V
V
OH
OH
Table 9
and
defines the TIP and RING voltage at
V
OHvirt
Figure 13
suggests a suitable value for
2 x 800
301
22
-36
150
(reference G in
. The overhead voltage is
C
LP
V
reference B.
OH
Rev. 2.0, 2005-04-14
also influences the
, depends on the
Unit
k
nF
dB
nF
PBL 38640/2
Battery Feed
FlexiSLIC
Figure
Figure 13
V
TRO
V
BAT
, is
13).
to