V23826-H18-C363 Infineon Technologies, V23826-H18-C363 Datasheet - Page 2

• Manufacturer Part Number: V23826-H18-C363
• Description: TXRX SINGLE MODE 622MBD 1X9
• Manufacturer: Infineon Technologies
• Series: -r

Specifications of V23826-H18-C363

• Data Rate: 622Mbps
• Wavelength: 1300nm
• Applications: Ethernet
• Voltage - Supply: 3.1 V ~ 3.5 V
• Connector Type: SC
• Mounting Type: PCB
• Lead Free Status / Rohs Status: Contains lead / RoHS non-compliant
• Other names: V23826-H18-C363IN

DESCRIPTION
The Infineon single mode ATM transceiver complies with the
ATM Forum's Network Compatible ATM for Local Network
Applications document and ANSI's Broadband ISDN—Cus-
tomer Installation Interfaces, Physical Media Dependent Speci-
fication, T1.646-1995, Bellcore - SONET OC-3 / IR-1 and OC-12 /
IR-1, ITU-T G.957 STM-1 / S.1.1 and STM-4 / S.4.1. ATM was
developed to facilitate solutions in multimedia applications and
real time transmission. The data rate is scalable, and the ATM
protocol is the basis of the broadband public networks being
standardized in the International Telecommunications Union
(ITU), the former International Telegraph and Telephone Consul-
tative Committee (CCITT). ATM can also be used in local private
applications.
The Infineon single mode ATM transceiver is a single unit com-
prised of a transmitter, a receiver, and an SC receptacle. This
design frees the customer from many alignment and PC board
layout concerns. The module is designed for low cost WAN
applications. It can be used as the network end device interface
in workstations, servers, and storage devices, and in a broad
range of network devices such as bridges, routers, and intelli-
gent hubs, as well as wide area ATM switches.
This transceiver operates at 622.080 Mbit/s from a single
power supply (+5 V or 3.3 V). The differential data inputs and
outputs are PECL compatible.
Fiber Optics
2
Functional Description
This transceiver is designed to transmit serial data via single
mode cable.
Functional Diagram
The receiver component converts the optical serial data into
PECL compatible electrical data (RD and RDnot). The Signal
Detect (SD, active high) shows whether optical data is
present
The transmitter converts electrical PECL compatible serial data
(TD and TDnot) into optical serial data.
This version contains an Input Signal Monitor (ISM), that
switches off the optical power if a continuously low level is
applied at Data Input.
The transmitter contains a laser driver circuit that drives the
modulation and bias current of the laser diode. The currents are
controlled by a power control circuit to guarantee constant out-
put power of the laser over temperature and aging.
The power control uses the output of the monitor PIN diode
(mechanically built into the laser coupling unit) as a controlling
signal, to prevent the laser power from exceeding the operating
limits.
Single fault condition is ensured by means of an integrated
automatic shutdown circuit that disables the laser when it
detects transmitter failures. A reset is only possible by turning
the power off, and then on again.
The transceiver contains a supervisory circuit to control the
power supply. This circuit generates an internal reset signal
whenever the supply voltage drops below the reset threshold.
It keeps the reset signal active for at least 15 milliseconds after
the voltage has risen above the reset threshold. During this
time the laser is inactive.
Note
1. We recommend to switch off the transmitter supply (V
transmitter input data is applied.
TD
TD
RD
RD
SD
(1)
.
Monitor
V23826-H18-C63/C363, SM 622 MBd ATM/SDH/SONET 1x9 Trx
Laser
Driver
Power
Control
Receiver
Signal Monitor and
Automatic Shut-Down
LEN
ISM*
RX Coupling Unit
Laser Coupling Unit
e/o
Laser
o/e
o/e
Single Mode Fiber
*DC/DC Version only
CC
-Tx) if no