AFCT-57J7ATPZ Avago Technologies US Inc., AFCT-57J7ATPZ Datasheet
AFCT-57J7ATPZ
Specifications of AFCT-57J7ATPZ
Related parts for AFCT-57J7ATPZ
AFCT-57J7ATPZ Summary of contents
Page 1
... ANSI Fibre Channel FC-PI-3 and compatible with IEEE 802.3 for gigabit applications enhancement to the conventional SFP interface defi ned in SFF-8074i, the AFCT-57J7ATPZ is compliant to SFF-8472 (digital diagnostic interface for SFP). Using the 2-wire serial interface defi ned in the SFP MSA, the ...
Page 2
... Installation The AFCT-57J7ATPZ can be installed in any SFF-8074i compliant Small Form Pluggable (SFP) port regardless of host equipment operating status. The AFCT-57J7ATPZ is hot-pluggable, allowing the module to be installed while the host system is operating and on-line. Upon insertion, the transceiver housing makes initial contact with the host board SFP cage, mitigating potential damage due to Electro-Static Discharge (ESD) ...
Page 3
... A2, byte 110, bit 2). Eye Safety Circuit The AFCT-57J7ATPZ provides Class 1 (single fault tolerant) eye safety by design and has been tested for compliance with the requirements listed in Table 1. The eye safety ...
Page 4
... It may also result in improper operation and possibly overstress the laser source. Performance degradation or device failure may result. Connection of the AFCT-57J7ATPZ to a light source not compliant with ANSI FC-PI or IEEE 802.3 specifi cations, operating above maximum operating conditions manner inconsistent with it’ ...
Page 5
... EMI Immunity (Susceptibility) Due to its shielded design, the EMI immunity of the AFCT- 57J7ATPZ exceeds typical industry standards. Flammability The AFCT-57J7ATPZ optical transceiver is made of metal and high strength, heat resistant, chemical resistant and UL 94V-0 fl ame retardant plastic A11 Performance Class 2 (> 1000 Volts) ...
Page 6
Tx_DISABLE Tx_FAULT SERDES IC PROTOCOL IC LOSS OF SIGNAL 4 k MODULE DETECT SCL SDA Figure 2. Typical application confi guration 0.1 0.1 F 10 F SFP MODULE HOST BOARD ...
Page 7
Table 2. Pin Description Pin Name Function/Description 1 VeeT Transmitter Ground 2 TX_FAULT Transmitter Fault Indication – High indicates a fault condition 3 TX_DISABLE Transmitter Disable – Module optical output disables on high or open 4 MOD-DEF2 Module Defi nition ...
Page 8
Table 3. Absolute Maximum Ratings Parameter Storage Temperature Case Operating Temperature Relative Humidity Supply Voltage Low Speed Input Voltage Notes: 1. Absolute Maximum Ratings are those values beyond which damage to the device may occur if these limits are exceeded ...
Page 9
Table 6. Transmitter and Receiver Electrical Characteristics (T = -40°C to 85°C, VccT, VccR = 3.3 V ± 10%) C Parameter High Speed Data Input: Transmitter Diff erential Input Voltage (TD +/-) High Speed Data Output: Receiver Diff erential Output ...
Page 10
Table 8. Receiver Optical Characteristics (T = -40°C to 85°C, VccT, VccR = 3.3 V ± 10%) C Parameter Input Optical Power [Overdrive] Input Optical Modulation Amplitude (Peak-to-Peak) (2.457 to 7.373 Gb/s) [Sensitivity] Return Loss Loss of Signal – Assert ...
Page 11
Table 10. Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics (T = -40°C to 85°C, VccT, VccR = 3.3 V ± 10%) C Parameter Transceiver Internal Temperature Accuracy Transceiver Internal Supply Voltage Accuracy Transmitter Laser DC Bias Current Accuracy Transmitted ...
Page 12
... Addresses 63 and 95 are checksums calculated (per SFF-8472 and SFF-8074) and stored prior to product shipment. 5. Addresses 68-83 specify the AFCT-57J7ATPZ ASCII serial number and will vary on a per unit basis. 6. Addresses 84-91 specify the AFCT-57J7ATPZ ASCII date code and will vary on a per date code basis. 12 ...
Page 13
... Transmitted average optical power (Tx Pwr) is decoded bit unsigned integer in increments of 0.1 W. 5. Received average optical power (Rx Pwr) is decoded bit unsigned integer in increments of 0.1 W. 6. Bytes 55-94 are not intended for use with AFCT-57J7ATPZ, but have been set to default values per SFF-8472. 7. Byte checksum calculated (per SFF-8472) and stored prior to product shipment. ...
Page 14
... Indicates transceiver is powered and real time sense data is ready Ready) Notes: 1. The response time for soft commands of the AFCT-57J7ATPZ is 100 msec as specifi ed by the MSA SFF-8472. 2. Bit 6 is logic OR’d with the SFP TX_DISABLE input pin 3 ... either asserted will disable the SFP transmitter. ...
Page 15
... Figure 5. Module drawing. 15 AFCT-57J7ATPZ ...
Page 16
X Y 16.25 MIN. PITCH B PCB EDGE 5.68 8.58 11.08 16.25 REF. 14.25 2.0 11x 3 5 3.2 0.9 20 PIN 1 10.93 9.6 0.8 TYP 1.55 0.05 0 ...
Page 17
MAX. 11.73 REF 9.8 MAX. PCB Figure 7. SFP assembly drawing. Customer Manufacturing Processes This module is pluggable and is not designed for aqueous wash, IR refl ow, or wave soldering processes. For ...