LPC1754FBD80,518 NXP Semiconductors, LPC1754FBD80,518 Datasheet - Page 64

• Manufacturer Part Number: LPC1754FBD80,518
• Description: IC MCU 32BIT 128KB FLASH 80LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC17xxr

Specifications of LPC1754FBD80,518

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 100MHz
• Connectivity: CAN, I²C, IrDA, Microwire, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 52
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 6x12b, D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-LQFP
• Package: 80LQFP
• Device Core: ARM Cortex M3
• Family Name: LPC1700
• Maximum Speed: 100 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 52
• Interface Type: CAN/I2C/SPI/UART/USB
• On-chip Adc: 6-chx12-bit
• Number Of Timers: 4
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

NXP Semiconductors
LPC1759_58_56_54_52_51
Product data sheet
Fig 31. LPC1759/58/56/54/52/51 USB device port configuration
14.2 Crystal oscillator XTAL input and component selection
LPC17xx
The input voltage to the on-chip oscillators is limited to 1.8 V. If the oscillator is driven by a
clock in slave mode, it is recommended that the input be coupled through a capacitor with
C
capacitor to ground C
mode, a minimum of 200 mV(RMS) is needed.
In slave mode the input clock signal should be coupled by means of a capacitor of 100 pF
(Figure
corresponds to a square wave signal with a signal swing of between 280 mV and 1.4 V.
The XTALOUT pin in this configuration can be left unconnected.
External components and models used in oscillation mode are shown in
Table 21
and the capacitances C
fundamental mode oscillation (the fundamental frequency is represented by L, C
R
not be larger than 7 pF. Parameters F
manufacturer.
Fig 32. Slave mode operation of the on-chip oscillator
i
S
= 100 pF. To limit the input voltage to the specified range, choose an additional
). Capacitance C
USB_UP_LED
USB_CONNECT
USB_D+
USB_D−
V
BUS
32), with an amplitude between 200 mV(RMS) and 1000 mV(RMS). This
and
Table
All information provided in this document is subject to legal disclaimers.
33 Ω
33 Ω
P
22. Since the feedback resistance is integrated on chip, only a crystal
in
g
V
which attenuates the input voltage by a factor C
Rev. 7 — 29 March 2011
Figure 33
X1
DD
and C
V
DD
X2
represents the parallel package capacitance and should
need to be connected externally in case of
OSC
XTAL1
LPC1759/58/56/54/52/51
LPC1xxx
C i
100 pF
, C
L
, R
S
002aae835
32-bit ARM Cortex-M3 microcontroller
C g
and C
P
are supplied by the crystal
V
SS
V
BUS
D+
D−
USB-B
connector
002aad943
i
/(C
© NXP B.V. 2011. All rights reserved.
Figure 33
i
+ C
g
). In slave
L
and
and in
64 of 74