DG441DJ+ Maxim Integrated Products, DG441DJ+ Datasheet - Page 6

• Manufacturer Part Number: DG441DJ+
• Description: IC SWITCH QUAD SPST 16DIP
• Manufacturer: Maxim Integrated Products

Specifications of DG441DJ+

• Function: Switch
• Circuit: 4 x SPST - NC
• On-state Resistance: 85 Ohm
• Voltage Supply Source: Single, Dual Supply
• Voltage - Supply, Single/dual (±): 10 V ~ 30 V, ±4.5 V ~ 20 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 16-DIP (0.300", 7.62mm)
• Number Of Switches: Quad
• Switch Configuration: SPST
• On Resistance (max): 100 Ohms
• On Time (max): 250 ns
• Off Time (max): 170 ns
• Off Isolation (typ): 60 dB
• Supply Voltage (max): 30 V
• Supply Voltage (min): 10 V
• Supply Current: 15 uA
• Maximum Power Dissipation: 842 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• Off State Leakage Current (max): 20 nA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Using supply voltages other than ±15V reduces the
analog signal range. The DG441/DG442 switches oper-
ate with ±4.5V to ±20V bipolar supplies or with a +10V
to +30V single supply; connect V- to 0V when operating
with a single supply. Also, all device types can operate
with unbalanced supplies such as +24V and -5V. The
Typical Operating Characteristics graphs show typical
on-resistance with ±20V, ±15V, ±10V, and ±5V sup-
Improved, Quad, SPST Analog Switches
6
1, 16, 9,
DIP/SO
2, 15,
3, 14,
10, 7
11, 6
12
13
—
_______________________________________________________________________________________
8
4
5
PIN
1, 12, 9,
QFN-EP
15, 14,
16, 13,
THIN
7, 6
8, 5
10
11
—
4
2
3
Operation with Supply Voltages
Applications Information
IN1–IN4 Input
D1–D4
NAME
S1–S4
GND
N.C.
V+
EP
V-
Analog Switch Drain Terminal
Analog Switch Source
Terminal
Negative-Supply Voltage Input
Ground
Not Internally Connected
Positive-Supply Voltage
Input—Connected to Substrate
Exposed Pad. Connect EP to
V+. Do not use EP as a sole
V+ connection. (Thin QFN
package only.)
Pin Description
Other Than ±15V
FUNCTION
plies. (Switching times increase by a factor of two or
more for operation at ±5V.)
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maxi-
mum ratings because stresses beyond the listed rat-
ings can cause permanent damage to the devices.
Always sequence V+ on first, followed by V- and logic
inputs. If power-supply sequencing is not possible, add
two small, external signal diodes in series with supply
pins for overvoltage protection (Figure 1). Adding exter-
nal diodes reduces the analog-signal range to 1V
below V+ and 1V above V-, but low switch resistance
and low leakage characteristics are unaffected. Device
operation is unchanged, and the difference between
V+ and V- should not exceed +44V.
Figure 1. Overvoltage Protection Using External Blocking Diodes
V g
D
Overvoltage Protection
V+
V-
S