PCF85116-3N NXP Semiconductors, PCF85116-3N Datasheet - Page 17

EEPROM 2048 X 8 EEPROM ISC 2.7V EXT

PCF85116-3N

Manufacturer Part Number
PCF85116-3N
Description
EEPROM 2048 X 8 EEPROM ISC 2.7V EXT
Manufacturer
NXP Semiconductors
Datasheet

Specifications of PCF85116-3N

Memory Size
16 Kbit
Organization
2 K x 8
Interface Type
I2C
Maximum Clock Frequency
0.4 MHz
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.7 V
Maximum Operating Current
1 mA
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
SOT-97
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
3.3 V, 5 V
Lead Free Status / Rohs Status
 Details
Other names
PCF85116-3P/01,112
Philips Semiconductors
9397 750 14217
Product data
14.3.2 Wave soldering
14.3.3 Manual soldering
Moisture sensitivity precautions, as indicated on packing, must be respected at all
times.
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 to 4 seconds at 250 C or
265 C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal of corrosive residues in
most applications.
Fix the component by first soldering two diagonally-opposite end leads. Use a low
voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time
must be limited to 10 seconds at up to 300 C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 to 5 seconds between 270 and 320 C.
below 240 C (SnPb process) or below 260 C (Pb-free process) for packages with
a thickness < 2.5 mm and a volume < 350 mm
Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45 angle
to the transport direction of the printed-circuit board. The footprint must
incorporate solder thieves downstream and at the side corners.
– for packages with a thickness
– for packages with a thickness < 2.5 mm and a volume
– larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be
– smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the
thick/large packages.
parallel to the transport direction of the printed-circuit board;
transport direction of the printed-circuit board.
Rev. 04 — 25 October 2004
2048
2.5 mm
8-bit CMOS EEPROM with I
3
so called small/thin packages.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
PCF85116-3
350 mm
2
C-bus interface
3
so called
17 of 21

Related parts for PCF85116-3N