LH28F800BGHE-BL85 Sharp Electronics, LH28F800BGHE-BL85 Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/6/602/sharp_electronics_sml.jpg)
LH28F800BGHE-BL85
Manufacturer Part Number
LH28F800BGHE-BL85
Description
Manufacturer
Sharp Electronics
Datasheet
1.LH28F800BGHE-BL85.pdf
(43 pages)
Specifications of LH28F800BGHE-BL85
Cell Type
NOR
Density
8Mb
Interface Type
Parallel
Boot Type
Bottom
Address Bus
19b
Operating Supply Voltage (typ)
3.3/5V
Operating Temp Range
-40C to 85C
Package Type
TSOP-I
Program/erase Volt (typ)
2.7/3.3/5/12V
Sync/async
Asynchronous
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
2.7/4.5V
Operating Supply Voltage (max)
3.6/5.5V
Word Size
16b
Number Of Words
512K
Supply Current
65mA
Mounting
Surface Mount
Pin Count
48
Lead Free Status / Rohs Status
Not Compliant
device selection control, and when active enables
the selected memory device. OE# is the data
output (DQ
the selected memory data onto the I/O bus. WE#
must be at V
Fig. 11 illustrates read cycle.
3.2 Output Disable
With OE# at a logic-high level (V
outputs are disabled. Output pins (DQ
placed in a high-impedance state.
3.3 Standby
CE# at a logic-high level (V
standby mode which substantially reduces device
power consumption. DQ
in a high-impedance state independent of OE#. If
deselected during block erase or word write, the
device continues functioning, and consuming active
power until the operation completes.
3.4 Deep Power-Down
RP# at V
In read modes, RP#-low deselects the memory,
places output drivers in a high-impedance state and
turns off all internal circuits. RP# must be held low
for a minimum of 100 ns. Time t
after return from power-down until initial memory
access outputs are valid. After this wake-up
interval, normal operation is restored. The CUI is
reset to read array mode and status register is set
to 80H.
During block erase or word write modes, RP#-low
will abort the operation. RY/BY# remains low until
the reset operation is complete. Memory contents
being altered are no longer valid; the data may be
partially erased or written. Time t
after RP# goes to logic-high (V
command can be written.
As with any automated device, it is important to
IL
0
initiates the deep power-down mode.
-DQ
IH
15
and RP# must be at V
) control and when active drives
0
-DQ
IH
) places the device in
15
outputs are placed
IH
PHQV
PHWL
) before another
IH
), the device
0
-DQ
is required
is required
IH
or V
15
) are
HH
.
- 9 -
assert RP# during system reset. When the system
comes out of reset, it expects to read from the flash
memory. Automated flash memories provide status
information when accessed during block erase or
word write modes. If a CPU reset occurs with no
flash memory reset, proper CPU initialization may
not occur because the flash memory may be
providing status information instead of array data.
SHARP’s flash memories allow proper CPU
initialization following a system reset through the
use of the RP# input. In this application, RP# is
controlled by the same RESET# signal that resets
the system CPU.
3.5 Read Identifier Codes Operation
The read identifier codes operation outputs the
manufacture code and device code (see Fig. 2).
Using the manufacture and device codes, the
system CPU can automatically match the device
with its proper algorithms.
3.6 Write
Writing commands to the CUI enable reading of
device data and identifier codes. They also control
inspection and clearing of the status register. When
V
additionally controls block erasure and word write.
The Block Erase command requires appropriate
command data and an address within the block to
be erased. The Word Write command requires the
command and address of the location to be written.
CC
LH28F800BG-L/BGH-L (FOR TSOP, CSP)
Fig. 2 Device Identifier Code Memory Map
7FFFF
00002
00001
00000
= V
CC1/2/3/4
and V
Future Implementation
Manufacture Code
Reserved for
Device Code
PP
= V
PPH1/2/3
, the CUI