SAA1064 NXP Semiconductors, SAA1064 Datasheet
SAA1064
Specifications of SAA1064
Available stocks
Related parts for SAA1064
SAA1064 Summary of contents
Page 1
... DATA SHEET SAA1064 4-digit LED-driver with I interface Product specification File under Integrated Circuits, IC01 INTEGRATED CIRCUITS 2 C-Bus February 1991 ...
Page 2
... Note 1. The positive current is defined as the conventional current flow into a device (sink current). PACKAGE OUTLINE SAA1064: 24-lead DIL; plastic with internal heat spreader (SOT101B); SOT101-1; 1996 August 30. SAA1064T: 24-lead mini-pack; plastic (SO-24; SOT137A); SOT137-1; 1996 August 30. February 1991 2 C-Bus interface ...
Page 3
... Philips Semiconductors 4-digit LED-driver with I February 1991 2 C-Bus interface 3 Product specification SAA1064 ...
Page 4
... MX1 11 multiplex output V 12 ground positive supply CC MX2 14 multiplex output P9 to P16 15-22 segment output 2 SDA 23 I C-Bus serial data line 2 SCL 24 I C-Bus serial clock line February 1991 2 C-Bus interface 4 Product specification SAA1064 Fig.2 Pinning diagram. ...
Page 5
... HEX 70, 72, 74 and 76 for writing and 71, 73, 75 and 77 for reading. All other addresses cannot be acknowledged by the circuit. February 1991 2 C-Bus interface a. READ mode. b. WRITE mode. A1 Fig.3 I C-Bus format. 5 Product specification SAA1064 = programmable address bits = subaddress bits = control bits = POWER RESET fl This results in EE ...
Page 6
... The MSBs correspond with the outputs P8 and P16, the LSBs with P1 and P9. Digit numbers are equal to their subaddresses (hex February 1991 2 C-Bus interface Product specification SUB-ADDRESS 00 control register 01 digit 1 02 digit 2 03 digit 3 04 digit 4 05 reserved, not used 06 reserved, not used 07 reserved, not used (1) SAA1064 FUNCTION ...
Page 7
... Fig.5. February 1991 2 C-Bus interface 2 C-Bus specification. For protection against positive voltage pulses on these inputs . This means that normal line voltage should not exceed 5,5 volt. Data will EE 7 Product specification SAA1064 ...
Page 8
... SO (on ceramic substrate) 24-lead SO (on printed circuit board) February 1991 2 C-Bus interface CONDITIONS tot P tot 23 1-11 outputs OFF I I/O T amb T stg 8 Product specification SAA1064 SYMBOL MIN. MAX. 0 200 1000 500 0 0.5 V 14- +85 55 +150 j-a UNIT ...
Page 9
... OFF 7 all outputs OFF 23,24 V IL(L) V 3,0 IH( 23, 23, OL( SDA 5/16V 1 V 9/16V 1 V 13/16V 140 140 Product specification SAA1064 MIN. TYP. MAX. 5,0 15 9,5 14,0 50 5,5 1 0,4 3/16V CC 3/8V 7/16V 5/8V 11/16V 3,3 CC 1,5 160 160 180 UNIT ...
Page 10
... Multiplexed duty factor * Value to be fixed. February 1991 2 C-Bus interface CONDITIONS SYMBOL 17 MPX MPX MPX MPX MPX EXT MPX 10 Product specification SAA1064 MIN. TYP. MAX. 0 25.2 3.0 3.6 6.0 7.2 12.0 14.4 7.5 1.5 110 70 110 10 48.4 UNIT ...
Page 11
... Philips Semiconductors 4-digit LED-driver with I February 1991 2 C-Bus interface Fig.4 Timing diagram. 11 Product specification SAA1064 ...
Page 12
... Philips Semiconductors 4-digit LED-driver with I APPLICATION INFORMATION February 1991 2 C-Bus interface Fig.5 Dynamic mode application diagram. 12 Product specification SAA1064 ...
Page 13
... Philips Semiconductors 4-digit LED-driver with I February 1991 2 C-Bus interface Fig.6 Static mode application diagram. 13 Product specification SAA1064 ...
Page 14
... LED-driver with I POWER DISSIPATION The total maximum power dissipation of the SAA1064 is made up by the following parts: 1. Maximum dissipation when none of the outputs are programmed (continuous line in Fig.7). 2. Maximum dissipation of each programmed output. The dashed line in Fig.7 visualises the dissipation when all the segments are programmed (max ...
Page 15
... LED-driver with I 750 handbook, full pagewidth dissipation (mW) 500 250 0 0 2.5 (1) All outputs programmed (no segment current sink). (2) Outputs not programmed. Fig.7 SAA1064 power dissipation as a function of supply voltage. February 1991 2 C-Bus interface 5.0 7.5 15 Product specification SAA1064 MEA104 (1) (2) 10 ...
Page 16
... REFERENCES JEDEC EIAJ MO-015AD 3.9 15.80 17.15 2.54 15.24 3.4 15.24 15.90 0.15 0.62 0.68 0.10 0.60 0.13 0.60 0.63 EUROPEAN PROJECTION Product specification SAA1064 SOT101-1 ( max. 0.25 2.2 0.01 0.087 ISSUE DATE 92-11-17 95-01-23 ...
Page 17
... REFERENCES JEDEC EIAJ MS-013AD detail 1.1 1.1 1.4 0.25 0.25 0.4 1.0 0.043 0.043 0.01 0.01 0.055 0.016 0.039 EUROPEAN PROJECTION Product specification SAA1064 SOT137 ( 0.9 0.1 0 0.035 0.004 0.016 ISSUE DATE 95-01-24 97-05-22 ...
Page 18
... Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 18 Product specification SAA1064 ...
Page 19
... Philips. This specification can be ordered using the code 9398 393 40011. February 1991 2 C-Bus interface 2 C components conveys a license under the Philips’ system provided the system conforms to the I 19 Product specification SAA1064 2 C patent to use the 2 C specification defined by ...