AM28F010-90JI Spansion Inc., AM28F010-90JI Datasheet - Page 9

• Manufacturer Part Number: AM28F010-90JI
• Manufacturer: Spansion Inc.

Specifications of AM28F010-90JI

• Cell Type: NOR
• Density: 1Mb
• Access Time (max): 90ns
• Interface Type: Parallel
• Boot Type: Not Required
• Address Bus: 17b
• Operating Supply Voltage (typ): 5V
• Operating Temp Range: -40C to 85C
• Package Type: PLCC
• Program/erase Volt (typ): 11.4 to 12.6V
• Sync/async: Asynchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (max): 5.5V
• Word Size: 8b
• Number Of Words: 128K
• Supply Current: 30mA
• Mounting: Surface Mount
• Pin Count: 32
• Lead Free Status / Rohs Status: Not Compliant

READ ONLY MODE
When V
is inactive. The device can either read array or autose-
lect data, or be standby mode.
Read
The device functions as a read only memory when V
< V
must be satisfied in order to output data. CE# controls
power to the device. This pin should be used for spe-
cific device selection. OE# controls the device outputs
and should be used to gate data to the output pins if a
device is selected.
Address access time t
stable addresses to valid output data. The chip enable
access time t
stable CE# to valid data at the output pins. The output
enable access time is the delay from the falling edge of
OE# to valid data at the output pins (assuming the ad-
dresses have been stable at least t
Standby Mode
The device has two standby modes. The CMOS
standby mode (CE# input held at V
sumes less than 100 µA of current. TTL standby mode
(CE# is held at V
to less than 1mA. When in the standby mode the out-
puts are in a high impedance state, independent of the
OE# input.
If the device is deselected during erasure, program-
ming, or program/erase verification, the device will
draw active current until the operation is terminated.
Output Disable
Output from the device is disabled when OE# is at a
logic high level. When disabled, output pins are in a
high impedance state.
Type
Manufacturer Code
Device Code
CC
+ 2 V. The device has two control functions. Both
PP
is less than V
CE
is the delay from stable addresses and
IH
) reduces the current requirements
ACC
CC
+ 2 V, the command register
is equal to the delay from
ACC
CC
Table 2. Am28F010 Auto Select Code
–t
OE
0.5 V), con-
).
Am28F010
PP
Auto Select
Flash memories can be programmed in-system or in a
standard PROM programmer. The device may be sol-
dered to the circuit board upon receipt of shipment and
programmed in-system. Alternatively, the device may
initially be programmed in a PROM programmer prior
to soldering the device to the board.
The Auto select mode allows the reading out of a binary
code from the device that will identify its manufacturer
and type. This mode is intended for the purpose
of automatically matching the device to be pro-
grammed with its corresponding programming algo-
r ith m. Thi s mo de is fu nct ion al ove r the en tir e
temperature range of the device.
Programming In A PROM Programmer
To activate this mode, the programming equipment
must force V
identifier bytes may then be sequenced from the device
outputs by toggling address A
address lines must be held at V
less than or equal to V
select mode. Byte 0 (A0 = V
turer code and byte 1 (A0 = V
code. For the device these two bytes are given in Table
2 below. All identifiers for manufacturer and device
codes will exhibit odd parity with the MSB (DQ7) de-
fined as the parity bit.
ID
(11.5 V to 13.0 V) on address A9. Two
CC
V
V
A0
IH
+ 2.0 V while using this Auto
IL
IL
) represents the manufac-
0
from V
IH
) the device identifier
IL
, and V
IL
to V
Code (HEX)
PP
IH
A7
01
. All other
must be
9