AFBR-57F5PZ Avago Technologies US Inc., AFBR-57F5PZ Datasheet
AFBR-57F5PZ
Specifications of AFBR-57F5PZ
Related parts for AFBR-57F5PZ
AFBR-57F5PZ Summary of contents
Page 1
... Fibre Channel speed negotiation. Digital diagnostic monitoring information (DMI) is pres- ent in the AFBR-57F5PZ per the requirements of SFF-8472, providing real time monitoring information of transceiver laser, receiver and environment conditions over a SFF- 8431 2-wire serial interface ...
Page 2
... Installation The AFBR-57F5PZ can be installed in any SFF-8074i com- pliant Small Form Pluggable (SFP) port regardless of host equipment operating status. The AFBR-57F5PZ is hot- pluggable, allowing the module to be installed while the host system is operating and on-line. Upon insertion, the transceiver housing makes initial contact with the host board SFP cage, mitigating potential damage due to Elec- tro-Static Discharge (ESD) ...
Page 3
... A2, byte 110, bit 2). Eye Safety Circuit The AFBR-57F5PZ provides Class 1 (single fault tolerant) eye safety by design and has been tested for compliance with the requirements listed in Table 1. The eye safety ...
Page 4
... AFBR-57F5PZ will void the product warranty. It may also result in improper operation and possibly overstress the laser source. Performance degrada tion or device fail- ure may result. Connection of the AFBR-57F5PZ to a light source not compliant with ANSI FC-PI specifi cations, oper- ating above maximum operating conditions man- ner inconsistent with it’ ...
Page 5
... Electrostatic Discharge (ESD) The AFBR-57F5PZ is compatible with ESD levels found in typical manufacturing and operating environments as de- scribed in Table 1. In the normal handling and operation of optical transceivers, ESD is of concern in two circum- stances. The fi rst case is during handling of the transceiver prior to insertion into an SFP compliant cage. To protect the de- vice, it’ ...
Page 6
Special Operation Functions: Pre Post Rx Rx Vout & Amp Amp CDR Emphasis μcontroller Laser Tx Driver CDR ality (i2c controlled) Figure 2a. OWRAP Function Electrical and optical high speed data “wrap” functions are enabled to assist with local host ...
Page 7
Tx Rate Select Tx_DISABLE Tx_FAULT SERDES IC PROTOCOL IC LOSS OF SIGNAL Rx Rate Select 4 kΩ MODULE DETECT SCL SDA Figure 3. Typical application confi guration 0.1 μF 22 μ ...
Page 8
Table 3. Pin Description Pin Name Function/Description 1 VeeT Transmitter Ground 2 TX_FAULT Transmitter Fault Indication – High indicates a fault condition 3 TX_DISABLE Transmitter Disable – Module electrical input disables on high or open 4 MOD-DEF2 Module Defi nition ...
Page 9
Table 4. Absolute Maximum Ratings Parameter Storage Temperature Case Operating Temperature Relative Humidity Supply Voltage Low Speed Input Voltage Notes; 1. Absolute Maximum Ratings are those values beyond which damage to the device may occur if these limits are exceeded ...
Page 10
Table 7. Transmitter and Receiver Electrical Characteristics (Tc = 0°C to 70°C, VccT, VccR = 3.3V +/- 5%) Parameter High Speed Data Input Transmitter Diff erential Input Voltage (TD+/-) High Speed Data Output Receiver Diff erential Output Voltage (RD+/-) Receiver ...
Page 11
Table 9. Receiver Optical and Electrical Characteristics (Tc = 0°C to 70°C, VccT, VccR = 3.3V +/- 5%) Parameter Optical Input Power Input Optical Modulation Amplitude, 14.025Gb/s (Peak to Peak) [Unstressed Sensitivity] Input Optical Modulation Amplitude, 8.5Gb/s (Peak to Peak) ...
Page 12
Table 10. Transceiver SOFT DIAGNOSTIC Timing Characteristics (T = 0°C to 70°C, VccT, VccR = 3.3 V ±5%) C Parameter Hardware TX_DISABLE Assert Time Hardware TX_DISABLE Negate Time Time to initialize, including reset of TX_FAULT Hardware TX_FAULT Assert Time Hardware ...
Page 13
Table 11. Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics (T = 0°C to 70°C, VccT, VccR = 3.3 V ±5%) C Parameter Transceiver Internal Temperature Accuracy Transceiver Internal Supply Voltage Accuracy Transmitter Laser DC Bias Current Accuracy Transmitted Average ...
Page 14
... Address 68-83 specify the AFBR-57F5PZ ASCII serial number and will vary on a per unit basis. 8. Address 84-91 specify the AFBR-57F5PZ ASCII data code and will vary on a per date code basis. 9. Link distance with OM3 50/125um cable at 8.5Gb/s is 150m. Link distance at 4.25Gb/s is 380m. ...
Page 15
... Transmitted average optical power (Tx Pwr) is decoded bit unsigned integer in increments of 0.1 μW. 5. Received average optical power (Rx Pwr) is decoded bit unsigned integer in increments of 0.1 μW. 6. Bytes 56-94 are not intended for use with AFBR-57F5PZ, but have been set to default values per SFF-8472. 7. Byte checksum calculated (per SFF-8472) and stored prior to product shipment. ...
Page 16
... Data Ready (Bar) Notes: 1. The response time for soft commands of the AFBR-57F5PZ is 100msec as specifi ed by MSA SFF-8472. 2. Bit 6 is logic OR’d with the SFP TX_DISABLE input pin 3 …. either asserted will disable the SFP transmitter. 3. Bit 3 is logic OR’d with the SFP RS(0) RX Rate_Select input pin 7 …. either asserted will set receiver to Rate = High. ...
Page 17
Table 16. EEPROM Serial ID Memory Contents – Alarms and Warnings (Address A2h, Bytes 112, 113, 116, 117) Byte Bit Flag Bit Name Description 112 7 Temp High Alarm 6 Temp Low Alarm 5 Vcc High Alarm 4 Vcc Low ...
Page 18
Table 17. EEPROM Serial ID Memory Contents – Soft Commands (Address A2h, Byte 118). Bit # Status/Control Name 4-7 Reserved 3 Soft RS(1) Control 2 Reserved 1 Power Level State 0 Power Level Select Notes: 1. Bit 3 is logic ...
Page 19
... LATCH COLOR BLACK 6.25 Figure 6. Module drawing. 19 13.6 13.7 0.94 UNCOMPRESSED 12.27 0.65 UNCOMPRESSED 47.5 AFBR-57F5PZ 850nm LASER PROD 21CRF(J) CLASS1 CHINA YYWW SN: A3YYWWCD1C 8.6 ...
Page 20
X Y 10x ˇ 1.05 ± 0.01 16.25 MIN. PITCH B PCB EDGE 5.68 8.58 11.08 16.25 REF . 14.25 2.0 11x 3 5 3.2 0.9 20 PIN 1 10.93 9.6 0.8 TYP 1.55 ± 0.05 ...
Page 21
MAX. 11.73 REF 9.8 MAX. PCB Figure 8. SFP Assembly drawing. Customer Manufacturing Processes This module is pluggable and is not designed for aqueous wash, IR refl ow, or wave ...
Page 22
Appendix I. Rate Select Control RX and TX rates can be independently controlled by either hardware input pins or via register writes. Module electrical input pins 7 and 9 are used to select RX and TX rate respectively. Status of ...