SI3201-GSR Silicon Laboratories Inc, SI3201-GSR Datasheet - Page 34
![SLIC 3.3V/3.3V/3.3V/5V/5V/5V](/photos/31/27/312732/16pin_soic_n_sml.jpg)
SI3201-GSR
Manufacturer Part Number
SI3201-GSR
Description
SLIC 3.3V/3.3V/3.3V/5V/5V/5V
Manufacturer
Silicon Laboratories Inc
Datasheet
1.SI3201-GSR.pdf
(122 pages)
Specifications of SI3201-GSR
Lead Free Status / Rohs Status
Compliant
Si3216
power supply (number of REN supported).
For this solution, an n-channel power MOSFET (M1)
switches the current flow through a power transformer
T1. T1 is specified in “AN45: Design Guide for the
Si3210/15/16 DC-DC Converter” and includes several
taps on the primary side to facilitate a wide range of
input voltages. The “M” version of the ProSLIC must be
used for the application circuit depicted in Figure 14 on
page 24 because the DCFF pin is used to drive M1
directly and, therefore, must be the same polarity as
DCDRV. DCDRV is not used in this circuit option;
connecting DCFF and DCDRV together is not
recommended.
2.2.4. DC-DC Converter Architecture
The control logic for a pulse-width modulated (PWM)
dc-dc converter is incorporated in the ProSLIC. Output
pins DCDRV and DCFF are used to switch a bipolar
transistor or MOSFET. The polarity of DCFF is opposite
that of DCDRV.
The dc-dc converter circuit is powered on when the
DCOF bit in the powerdown register (direct Register 14,
bit 4) is cleared to 0. The switching regulator circuit
within the ProSLIC is a high-performance, pulse-width
modulation controller. The control pins are driven by the
PWM controller logic in the ProSLIC. The regulated
output voltage (V
used to detect whether the output voltage is above or
below an internal reference for the desired battery
voltage. The dc monitor pins SDCH and SDCL monitor
input current and voltage to the dc-dc converter external
circuitry. If an overload condition is detected, the PWM
controller will turn off the switching transistor for the
remainder of a PWM period to prevent damage to
external components. It is important that the proper
value of R18 be selected to ensure safe operation.
Guidance is given in “AN45: Design Guide for the
Si3210/15/16 DC-DC Converter”.
The PWM controller operates at a frequency set by the
dc-dc Converter PWM register (direct Register 92).
During a PWM period the outputs of the control pins
DCDRV and DCFF are asserted for a time given by the
read-only
Register 94).
The dc-dc converter must be off for some time in each
cycle to allow the inductor or transformer to transfer its
stored energy to the output capacitor, C9. This minimum
off time can be set through the dc-dc Converter
Switching Delay register, (direct Register 93). The
number of 16.384 MHz clock cycles that the controller is
off is equal to DCTOF (bits 0 through 4) plus 4. If the dc
monitor pins detect an overload condition, the dc-dc
converter interrupts its conversion cycles regardless of
34
PWM
BAT
) is sensed by the SVBAT pin and
Pulse
Width
register
(direct
Rev. 1.0
the register settings to prevent component damage.
These inputs should be calibrated by writing the DCCAL
bit (bit 7) of the dc-dc Converter Switching Delay
register, direct Register 93, after the dc-dc converter
has been turned on.
Because the ProSLIC dynamically regulates its own
battery supply voltage using the dc-dc converter
controller, the battery voltage (V
negative-most terminal by a programmable voltage
(V
signals.
As mentioned previously, the ProSLIC dynamically
adjusts V
illustrate this, the behavior of V
shown in Figure 19. In the Active state, the TIP-to-RING
open circuit voltage is kept at V
voltage region while the regulator output voltage,
V
When the loop current attempts to exceed I
line driver circuit enters constant current mode allowing
the TIP to RING voltage to track R
terminal is kept at a constant voltage, it is the RING
terminal voltage that tracks R
|V
|V
decreases below the VOC/I
output
(TRACK = 1), or the R
stopped when |V
former case is the more common application and
provides the maximum power dissipation savings. In
principle, the regulator output voltage can go as low as
|V
When TRACK = 0, |V
V
to decrease with decreasing R
dissipation on the NPN bipolar transistor driving the
RING terminal can become large and may require a
higher power rating device. The non-tracking mode of
operation is required by specific terminal equipment
which, in order to initiate certain data transmission
modes, goes briefly on-hook to measure the line voltage
to determine whether there is any other off-hook
terminal equipment on the same line. TRACK = 0 mode
is desired since the regulator output voltage has long
settling time constants (tens of milliseconds) and cannot
change rapidly for TRACK = 1 mode. Therefore, the
brief on-hook voltage measurement would yield
approximately the same voltage as the off-hook line
voltage and would cause the terminal equipment to
incorrectly sense another off-hook terminal.
BAT
BATL
BAT
BAT
BAT
OV
) to allow voltage headroom for carrying audio
= V
| voltage will also track R
| = I
| = V
. The RING terminal voltage, however, continues
CM
voltage
BAT
LIM
CM
+ V
+ V
to suit the particular circuit requirement. To
x R
OC
OV
LOOP
, offering significant power savings.
can
+ V
BAT
OV
BAT
| = |V
.
LOOP
+ V
continue
| does not decrease below
BATL
LOOP
CM
LIM
BAT
tracking mechanism is
BAT
| (TRACK = 0). The
LOOP
+ V
mark, the regulator
in the Active state is
and, as a result, the
OC
LOOP
) is offset from the
to
LOOP
in the constant
. In this state,
OV
. The power
track
. As R
. As the TIP
LIM
, the dc
R
LOOP
LOOP