ATA557001C-DDB Atmel, ATA557001C-DDB Datasheet
ATA557001C-DDB
Specifications of ATA557001C-DDB
Related parts for ATA557001C-DDB
ATA557001C-DDB Summary of contents
Page 1
... Separate 64-bit Memory for Traceability Data • 32-bit Configuration Register in EEPROM to Setup – Data Rate • RF/2 to RF/128, Binary Selectable or • Fixed Atmel e5550 Data Rates – Modulation/Coding • FSK, PSK, Manchester, Bi-phase, NRZ – Other Options • Password Mode • Maximum Block Feature • ...
Page 2
... System Block Diagram Figure 2-1. RFID System Using Atmel Reader Base station or Base station 3. ATA5570C – Building Blocks Figure 3-1. 3.1 Analog Front End (AFE) The AFE includes all circuits which are directly connected to the coil. It generates the IC’s power supply and handles the bi-directional data communication with the reader. It consists of the following blocks: • ...
Page 3
... POR event or reset com- mand. On delivery, the mode register is preprogrammed with the value 0014 8000h which corresponds to continuous read of block 0, Manchester coded, RF/64. 9191B–RFID–05/11 Atmel ATA5570C ® e5550/e5551 and Atmel T5554 bit rates (RF/8, RF/16, RF/32, 3 ...
Page 4
... Figure 3-2. Block 0 Configuration Mapping – Atmel Master Key Note 1 Unlocked 1 Locked 1) If Master Key = 6 then test mode write commands are ignored 2) If Master Key < > then extended function mode is disabled 3.10 Modulator The modulator consists of data encoders for the following basic types of modulation: Table 3-1 ...
Page 5
... Blocks 1 and 2 of page 1 contain traceability data and are transmitted with the modulation parameters defined in the configuration register after the opcode “11” is issued by the reader (Figure 4-6 on page Figure 3-3. 9191B–RFID–05/11 11). These traceability data blocks are programmed and locked by Atmel. Memory Map ...
Page 6
... Atmel and/or foundry version of the Atmel ATA5570C. The lower 40 bits of the data encode Atmel’s traceability information and conform to a unique numbering system (unique ID). These 40 data bits contain LotID (Year, Quarter, Number), Wafernumber (Wafer#) and die number on wafer (DW). ...
Page 7
... Every time the Atmel is a logical “0”. The data stream starts with block 1, bit 1, continues through MAXBLK, bit 32, and cycles continuously if in regular-read mode. This behavior is different from the original Atmel e555x and helps to decode PSK-modulated data. 9191B–RFID–05/11 ...
Page 8
... BLK-limited read data stream. In block-read mode, after any block-write or direct access command MAXBLK was set to “0” or “1”, the sequence terminator is inserted before the transmission of the selected block. This behavior is different from former Atmel e5550-compatible ICs (Atmel T5551, Atmel T5554). Figure 4-2. ...
Page 9
... When there is no gap for more than 64 field clocks after a previous gap, the Atmel ATA5570C exits the write mode. The tag starts with the command execution if the correct number of bits were received. If there is a failure detected the Atmel ATA5570C does not continue and will enter regular-read mode. ...
Page 10
... For the AOR wake-up command an opcode and a valid password are necessary to select and activate a specific tag Note: If the transmitted command sequence is invalid, the Atmel ATA5570C enters regular-read mode with the previously selected page (by former opcode “10” or “11”). Figure 4-5. ...
Page 11
... Answer-on-request (AOR) Mode When the AOR bit is set, the Atmel ATA5570C does not start modulation in the regular-read mode after loading configuration block 0. The tag waits for a valid AOR data stream (“wake-up command”) from the reader before modulation is enabled. The wake-up command consists of the opcode (“ ...
Page 12
... Answer-on-request (AOR) Mode V Coil 1 - Coil 2 Loading block 0 POR Figure 4-8. Coil Voltage After Programming of a Memory Block V Coil 1- Coil 2 Write data to tag Atmel ATA5570C 12 No modulation because AOR = 1 Read programmed 5.6 ms memory block Programming and (Block-read mode) data verification De-activate Function ...
Page 13
... W "Select a single tag" Send OPCODE + PWD => "wake up command" Decode data NO All tags read ? YES Field ON => OFF EXIT Atmel ATA5570C Tag Field OFF => ON POWER ON RESET Read configuration Enter AOR mode Wait for OPCODE + PWD => "wake up command" Receive damping ON NO Password correct ? Send block 1 ...
Page 14
... If the command sequence was received successfully, the following error could still prevent programming: • The lock bit of the addressed block is already set In case of a locked block, programming mode will not be entered. The Atmel ATA5570C reverts to block-read mode, continuously transmitting the currently addressed block. Atmel ATA5570C 14 This timing and behavior is different from the e555x-family predecessors ...
Page 15
... Command Decode single gap OP(11..) Page 1 OP(10..) OP(00) Write OP(1p)* Write Number of bits Password check Lock bit check Program and Verify Atmel ATA5570C AOR = 1 AOR Mode Page Block-read Mode gap addr = current Direct access OP (1p)* OP (1p)* Page 0 OP(01) Test-mode if master key <> 6 ...
Page 16
... OTP Functionality If the OTP bit is set to “1”, all memory blocks are write protected and behave as if all lock bits are set to “1”. If, additionally, the master key is set to “6”, the Atmel ation is locked forever (= OTP functionality). If the master key is set to “9”, the test-mode access allows the re-configuration of the tag. ...
Page 17
... Bi-phase 1 (’50) “1” creates an additional mid-bit change “0” creates an additional mid-bit change Bi-phase 2 (’57) “0” creates an additional mid-bit change “1” creates an additional mid-bit change NRZ Notes: 6.3 Sequence Start Marker Figure 6-2. Atmel ATA5570C Sequence Start Marker in Extended Mode Sequence Start Marker 10 Block n Block-read mode 10 Block 1 ...
Page 18
... Inverse Data Output The Atmel ATA5570C supports in its extended mode (X-mode) an inverse data output option. If inverse data is enabled, the modulator as shown in Table modulation, when R Figure 6-3. Data Encoder for Inverse Data Output Sensor in Intern out data D Sync Data clock CLK R 6 ...
Page 19
... Figure 6-4. 9191B–RFID–05/11 Example of Manchester Coding With Data Rate RF/16 Atmel ATA5570C 19 ...
Page 20
... Figure 6-5. Atmel ATA5570C 20 Example of Bi-phase Coding With Data Rate RF/16 9191B–RFID–05/11 ...
Page 21
... Figure 6-6. 9191B–RFID–05/11 Example: FSK1a Coding With Data Rate RF/40, Subcarrier f Atmel ATA5570C = RF/ RF ...
Page 22
... Figure 6-7. Atmel ATA5570C 22 Example of PSK1 Coding With Data Rate RF/16 9191B–RFID–05/11 ...
Page 23
... Figure 6-8. 9191B–RFID–05/11 Example of PSK2 Coding With Data Rate RF/16 Atmel ATA5570C 23 ...
Page 24
... Figure 6-9. Atmel ATA5570C 24 Example of PSK3 Coding With Data Rate RF/16 9191B–RFID–05/11 ...
Page 25
... Pin Symbol 25° –25°C to +85°C ( coil clamp t startup = 55°C t retention = 150°C t retention n cycle Figure 2-1 on page Atmel ATA5570C Value 20 20 100 –25 to +105 –40 to +150 Min Typ Max 100 125 150 RF 1 clamp 100,000 50 100 ...
Page 26
... Reliability Parameters Electrostatic discharge ESD S.5.1 (Human Body Model) Electrostatic discharge JEDEC A115A (Machine Model) Lifetime in SO8 at T =150°C op Figure 9-1. 10. Ordering Information Extended Type Number ATA557001C-DDB ATA557001C-DDT ATA557001C-TAQY Atmel ATA5570C 26 Measurement Setup for I and OUTmax Package 6” sawn wafer on foil with ring, thickness 150µ ...
Page 27
... Package Information Figure 11-1. Pad Layout Dimensions in µm C2 1030 292 112.5 9191B–RFID–05/11 1020 100 100 573 VSS SENS 105.5 80 Atmel ATA5570C 135 C1 130 80 ATA5570 100 70 27 ...
Page 28
... Figure 11-2. Sawn Wafer on Foil with Ring Die Dimensions 20:1 technical drawings according to DIN specifications Dimensions in mm Orientation on frame Option xx 01 Package Drawing Contact: packagedrawings@atmel.com Atmel ATA5570C 28 0 (0.1) 0.08 59.5 63.6 B 227.7 Ø 150 Ø Ø 194.5 Ø A 212 TITLE ...
Page 29
... B0 Chip orientation Chip identification ATA5570 TITLE Chip Dimensions ATA5570xxC-DDT Atmel ATA5570C technical drawings according to DIN specifications Dimensions in mm 0.0035 ±0.001 Polyimide Option 5:1 Tray: H20-050x12 Material: PS, black, conductive Qty. per tray: 400 ...
Page 30
... Figure 11-4. SO8 Package Package Dimensions in mm 0.4 1.27 Drawing-No.: 6.541-5031.01-4 Issue: 1; 15.08.06 Atmel ATA5570C 30 4.9 ±0.1 3. ±0.2 3.7 ±0.1 3.8 ±0.1 6 ±0.2 technical drawings according to DIN specifications 9191B–RFID–05/11 ...
Page 31
... Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. 9191B-RFID-05/11 9191B–RFID–05/ COIL1 2 7 COIL2 SENS 4 5 VSS History Figure 3-2 “Block 0 Configuration Mapping – Atmel Mode” on page 4 changed Atmel ATA5570C ® e5550 Compatibility 31 ...
Page 32
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellec- tual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICU- LAR PURPOSE, OR NON-INFRINGEMENT ...