MT36VDDF25672Y-335J1 Micron Technology Inc, MT36VDDF25672Y-335J1 Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT36VDDF25672Y-335J1
Manufacturer Part Number
MT36VDDF25672Y-335J1
Description
MODULE DDR SDRAM 2GB 184RDIMM
Manufacturer
Micron Technology Inc
Series
-r
Datasheet
1.MT36VDDF25672Y-335J1.pdf
(20 pages)
Specifications of MT36VDDF25672Y-335J1
Memory Type
DDR SDRAM
Memory Size
2GB
Speed
333MT/s
Features
-
Package / Case
184-RDIMM
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Table 6:
PDF: 09005aef80772fd2/Source: 09005aef8075ebf6
DDF36C128_256x72.fm - Rev. G 9/08 EN
RAS#, CAS#, WE#
DQS0–DQS17
CKE0, CKE1
DQ0–DQ63
CK0, CK0#
V
BA0, BA1
SA0–SA2
CB0–CB7
Symbol
S0#, S1#
A0–A12
RESET#
DD
V
Pin Descriptions
SDA
DDSPD
V
SCL
V
NC
/V
REF
SS
DD
Q
Supply
Supply
Supply
Supply
Input
Input
Input
Input
Input
Input
Input
Input
Input
Type
I/O
I/O
I/O
I/O
–
Description
Address inputs: Provide the row address for ACTIVE commands, and the
column address and auto precharge bit (A10) for READ/WRITE commands, to
select one location out of the memory array in the respective device bank. A10
sampled during a PRECHARGE command determines whether the PRECHARGE
applies to one device bank (A10 LOW, device bank selected by BA0, BA1) or all
device banks (A10 HIGH). The address inputs also provide the op-code during a
MODE REGISTER SET command. BA0 and BA1 define which mode register
(mode register or extended mode register) is loaded during the LOAD MODE
REGISTER command.
Bank address: BA0 and BA1 define the device bank to which an ACTIVE,
READ, WRITE, or PRECHARGE command is being applied.
Clock: CK and CK# are differential clock inputs. All address and control input
signals are sampled on the crossing of the positive edge of CK and the
negative edge of CK#. Output data (DQ and DQS) is referenced to the
crossings of CK and CK#.
Clock enable: CKE enables (registered HIGH) and CKE disables (registered
LOW) the internal clock, input buffers, and output drivers.
Command inputs: RAS#, CAS#, and WE# (along with S#) define the command
being entered.
Reset: Asynchronously forces all registered outputs LOW when RESET# is LOW.
This signal can be used during power-up to ensure that CKE is LOW and DQ are
High-Z.
Chip selects: S# enables (registered LOW) and disables (registered HIGH) the
command decoder.
Presence-detect address inputs: These pins are used to configure the SPD
EEPROM address range on the I
Serial clock for SPD EEPROM: SCL is used to synchronize the presence-detect
data transfer to and from the module.
Check bits.
Data input/output: Data bus.
Data strobe: Output with read data. Edge-aligned with read data. Input with
write data. Center-aligned with write data. Used to capture data.
Serial data: SDA is a bidirectional pin used to transfer addresses and data into
and out of the presence-detect portion of the module.
Power supply: +2.5V ±0.2V (-40B: +2.6V ±0.1V).
SPD EEPROM power supply: +2.3V to +3.6V.
SSTL_2 reference voltage (V
Ground.
No connect: These pins are not connected on the module.
1GB, 2GB (x72, ECC, DR) 184-Pin DDR SDRAM RDIMM
5
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD
/2).
Pin Assignments and Descriptions
2
C bus.
©2002 Micron Technology, Inc. All rights reserved.