SI3016-F-FS Silicon Laboratories Inc, SI3016-F-FS Datasheet - Page 6

• Manufacturer Part Number: SI3016-F-FS
• Description: IC ISOMODEM LINE-SIDE DAA 16SOIC
• Manufacturer: Silicon Laboratories Inc
• Type: Chipsetr

Specifications of SI3016-F-FS

• Package / Case: 16-SOIC (3.9mm Width)
• Data Format: V.90
• Baud Rates: 56k
• Interface: Serial
• Voltage - Supply: 3.3V, 5V
• Mounting Type: Surface Mount
• Product: Modem Chip
• Supply Current: 0.3 mA
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 4. AC Characteristics
(T
Table 3. DC Characteristics
(T
Parameter
Sample Rate
Transmit Frequency Response
Receive Frequency Response
Transmit Full Scale Level
Receive Full Scale Level
Dynamic Range
Dynamic Range
Dynamic Range
Transmit Total Harmonic Distortion
Transmit Total Harmonic Distortion
Receive Total Harmonic Distortion
Receive Total Harmonic Distortion
Dynamic Range (Caller ID mode)
Notes:
Si3016
6
Parameter
Input Leakage Current
Power Supply Current, Analog*
*Note: This current is required from the integrated system-side interface to communicate with the Si3016 through the isolation
A
A
=
=
1. Measured at TIP and RING with 600 Ω termination at 1 kHz, as shown in Figure 1.
2. R2 should be changed to a 243 Ω resistor when the FULLSCALE bit (FULL) is set to 1 (Register 18, bit 7).
3. Receive full scale level will produce –0.9 dBFS at SDO.
4. DR
5. Measurement is 300 to 3400 Hz. Applies to both transmit and receive paths.
6. Vin
7. Vin
8. THD
9. The AOUT pin is an optional pin located on the integrated system-side module. V
0 to 70 °C for K-Grade and –40 to 85 °C for B-Grade; see Figure 6 on page 9)
0 to 70 °C for K-Grade and –40 to 85 °C for B-Grade)
the integrated system-side module.
interface.
=
=
=
=
20 x log |Vin| + 20 x log (RMS signal/RMS noise).
1 kHz, –3 dBFS, Fs
1 KHz, –6 dBFS, Fs
20 x log (RMS distortion/RMS signal).
4,5,6
4,5,7
4,5,6
1,3
1
=
=
10300 Hz.
10300 Hz.
7,8
6,8
6,8
7,8
Symbol
Symbol
DR
THD
THD
THD
THD
V
V
DR
DR
DR
Fs
I
FS
FS
I
CID
L
A
ACT=1, DCT=11 (CTR21)
ACT=1, DCT=11(CTR21)
ACT=0, DCT=01 (Japan)
ACT=0, DCT=01 (Japan)
ACT=0, DCT=01 (Japan)
ACT=0, DCT=10 (FCC)
ACT=0, DCT=10 (FCC)
FULL = 1 (+3.2 dBm)
FULL = 1 (+3.2 dBm)
VIN = 1 kHz, –13 dBm
Low –3 dBFS Corner
Low –3 dBFS Corner
Rev. 1.0
FULL = 0 (–1 dBm)
FULL = 0 (–1 dBm)
Test Condition
Fs = F
Test Condition
I
I
L
I
I
L
I
I
I
L
L
L
L
L
=100 mA
=100 mA
=20 mA
=60 mA
=20 mA
=20 mA
=60 mA
PLL2
/5120
2
3
Min
–10
—
D
Min
7.2
refers to the digital power supply of
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Typ
0.3
—
1.58
1.58
Typ
–85
–76
–74
–82
82
83
84
60
—
0
5
1
1
Max
10
11.025
—
Max
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Unit
V
V
V
V
mA
µA
Unit
KHz
PEAK
PEAK
PEAK
PEAK
Hz
Hz
dB
dB
dB
dB
dB
dB
dB
dB