ADV7189BKSTZ Analog Devices Inc, ADV7189BKSTZ Datasheet - Page 41

• Manufacturer Part Number: ADV7189BKSTZ
• Description: IC DECODER VIDEO W/ADC 80LQFP
• Manufacturer: Analog Devices Inc
• Type: Video Decoderr

Specifications of ADV7189BKSTZ

• Applications: Set-Top Boxes, Video Players, Recorders
• Voltage - Supply, Analog: 3.15 V ~ 3.45 V
• Voltage - Supply, Digital: 1.65 V ~ 2 V
• Mounting Type: Surface Mount
• Package / Case: 80-LQFP
• Resolution (bits): 12bit
• Input Format: Analog
• Output Format: Digital
• Adc Sample Rate: 54MSPS
• Power Dissipation Pd: 450mW
• No. Of Input Channels: 12
• Supply Voltage Range: 3V To 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

VS and FIELD Configuration
The following controls allow the user to configure the behav-
ior of the VS and FIELD output pins, as well as to generate
embedded AV codes:
•
•
•
•
•
•
•
NEWAVMODE New AV Mode, Address 0x31[4]
When NEWAVMODE is 0, EAV/SAV codes are generated to
suit ADI encoders. No adjustments are possible.
Setting NEWAVMODE to 1 (default) enables the manual
position of the VSYNC, Field, and AV codes using
Registers 0x34 to 0x37 and Register 0xE5 to 0xEA. Default
register settings are CCIR656 compliant; see
and
see
for PAL.
HVSTIM Horizontal VS Timing, Address 0x31[3]
The HVSTIM bit allows the user to select where the VS signal
is being asserted within a line of video. Some interface circuitry
can require VS to go low while HS is low.
When HVSTIM is 0 (default) the start of the line is relative
to HSE.
When HVSTIM is 1, the start of the line is relative to HSB.
T able 56 and
2 0 9 H
•
•
•
•
•
•
F igure 26 for PAL. For recommended manual user settings,
2 0 8 H
ADV encoder-compatible signals via NEWAVMODE
PVS, PF
HVSTIM
VSBHO, VSBHE
VSEHO, VSEHE
For NTSC control:
For PAL control:
NVBEGDELO, NVBEGDELE, NVBEGSIGN,
NVBEG[4:0]
NVENDDELO, NVENDDELE, NVENDSIGN,
NVEND[4:0]
NFTOGDELO, NFTOGDELE, NFTOGSIGN,
NFTOG[4:0]
PVBEGDELO, PVBEGDELE, PVBEGSIGN,
PVBEG[4:0]
PVENDDELO, PVENDDELE, PVENDSIGN,
PVEND[4:0]
PFTOGDELO, PFTOGDELE, PFTOGSIGN,
PFTOG[4:0]
F igure 22 for NTSC; see
2 1 0 H
T able 57 and
2 1 1 H
F igure 21 for NTSC
2 0 7 H
F igure 27
2 1 2 H
Rev. B | Page 41 of 104
VSBHO VS Begin Horizontal Position Odd, Address 0x32[7]
The VSBHO and VSBHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to change state only
when HS is high/low.
When VSBHO is 0 (default), the VS pin goes high at the middle
of a line of video (odd field).
When VSBHO is 1, the VS pin changes state at the start of a line
(odd field).
VSBHE VS Begin Horizontal Position Even, Address 0x32[6]
The VSBHO and VSBHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to change state only
when HS is high/low.
When VSBHE is 0 (default), the VS pin goes high at the middle
of a line of video (even field).
When VSBHE is 1, the VS pin changes state at the start of a line
(even field).
VSEHO VS End Horizontal Position Odd, Address 0x33{7]
The VSEHO and VSEHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to change state only
when HS is high/low.
When VSEHO is 0, the VS pin goes low (inactive) at the middle
of a line of video (odd field).
When VSEHO is 1 (default), the VS pin changes state at the
start of a line (odd field).
VSEHE VS End Horizontal Position Even, Address 0x33[6]
The VSEHO and VSEHE bits select the position within a line at
which the VS pin (not the bit in the AV code) becomes active.
Some follow-on chips require the VS pin to change state only
when HS is high/low.
When VSEHE is 0 (default), the VS pin goes low (inactive) at
the middle of a line of video (even field).
When VSEHE is 1, the VS pin changes state at the start of a line
(even field).
PVS Polarity VS, Address 0x37[5]
The polarity of the VS pin can be inverted using the PVS bit.
When PVS is 0 (default), VS is active high. When PVS is 1, VS is
active low.
PF Polarity FIELD, Address 0x37[3]
The polarity of the FIELD pin can be inverted using the PF bit.
When PF is 0 (default), FIELD is active high. When PF is 1,
FIELD is active low.
ADV7189B