MAXQ2000-QAX Maxim Integrated Products, MAXQ2000-QAX Datasheet - Page 38
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAXQ2000-QAX
Manufacturer Part Number
MAXQ2000-QAX
Description
Microcontrollers (MCU) Low-Power LCD MCU
Manufacturer
Maxim Integrated Products
Datasheet
1.MAXQ2000-RAX.pdf
(38 pages)
Specifications of MAXQ2000-QAX
Processor Series
MAXQ2000
Core
RISC
Data Bus Width
16 bit
Program Memory Type
Flash
Program Memory Size
64 KB
Data Ram Size
2 KB
Interface Type
1-Wire, SPI, JTAG, UART
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
50
Number Of Timers
3
Operating Supply Voltage
1.8 V to 2.75 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
QFN-68
Development Tools By Supplier
MAXQ2000-KIT
Minimum Operating Temperature
- 40 C
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
38 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2008 Maxim Integrated Products
Low-Power LCD Microcontroller
REVISION
NUMBER
0
1
2
3
4
5
6
7
8
9
is a registered trademark of Dallas Semiconductor Corporation.
REVISION
DATE
10/04
10/04
12/04
10/05
12/06
6/05
1/06
3/06
6/06
3/08
Initial release for QFN package variant.
New product release for TQFN package variant.
In the Features section under Peripheral Features, corrected accumulator to
show 48 bits (not 40 bits).
In the Electrical Characteristics table, added Active Current line for 2.2V,
20MHz flash operation; V
updated V
Replaced the package drawing for 56-pin package.
Added lead-free part numbers to the Ordering Information table.
In the Electrical Characteristics table under LCD Segment Voltage, clarified
wording on V
ISEGxx to 3μA.
Clarified that flash memory write/erase cycles and data retention specifications
are at +25°C.
Clarified V
values (0.8 x V
test program values (0.8 x V
presented values to test program values (0.2 x V
affect the testing or operation of the device.
Corrected typo on pin 38 (Pin Configuration) from P4/
Corrected Pb-free package number denotations. Should be MAXQ2000-RAX+
and MAXQ2000-RBX+.
Added Revision A3 typ and max conditions to I
Characteristics table.
Added 100-pin LQFP package.
Added EP lines and note to QFN and TQFN pin configurations.
Changed 4kWords Utility ROM (Memory Organization section) to 4kB.
Changed 4k x 16 Utility ROM (Figure 1) to 2k x 16 Utility ROM, changed 8FFFh
to 87FFh.
Changed 4kWord to 4kB (Utility ROM section).
Added V
Corrected references of
In the
rate specification is met.
Added QFN and TQFN package codes to the Ordering Information table;
removed package drawings and replaced with Package Information table.
Typical Operating
DD
IH
IH1
slew rate specification to Electrical Characteristics table.
, V
ADJ
/V
IL
DDIO
IH3
, V
spec to V
OH
specifications, matching presented values to test program
); clarified VIH2 specification, matching presented values to
, and V
Circuit, added the reset monitor to ensure the V
IH2(MIN)
ADJ(MIN)
LCD
OL
to
data to match GBD/FTEC data.
); clarified V
DESCRIPTION
changed from 0.8 x V
= V
.
ADJ
and V
is a registered trademark of Maxim Integrated Products, Inc.
IL2
specification, matching
DD6
ADJ(MIN)
DDIO
in the Electrical
). These changes do not
DDIO
to P5.4/
= 0.1V; changed
to 0.75 x V
.
DDIO
DD
Revision History
slew
;
1, 7–11, 30, 35, 42
CHANGED
1, 30, 34
PAGES
33, 34
2, 3
2, 3
5, 6
38
33
13
14
15
36
37
—
1
1
1
3
4
2
2