S29GL512S10DHI020 Spansion Inc., S29GL512S10DHI020 Datasheet - Page 44
![no-image](/images/manufacturer_photos/0/6/621/spansion_inc__sml.jpg)
S29GL512S10DHI020
Manufacturer Part Number
S29GL512S10DHI020
Description
IC 512 MBIT, 3V, 100NS, 64-BALL FBGA, PAGE MODE
Manufacturer
Spansion Inc.
Datasheet
1.S29GL512S10DHI020.pdf
(97 pages)
Specifications of S29GL512S10DHI020
Lead Free Status / Rohs Status
Supplier Unconfirmed
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
S29GL512S10DHI020
Manufacturer:
SPANSION
Quantity:
20 000
5.5
44
5.5.1
5.4.3.7
Error Types and Clearing Procedures
Embedded Operation Error
DQ1: Write-to-Buffer Abort
DQ1 indicates whether a Write-to-Buffer operation was aborted. Under these conditions DQ1 produces a '1'.
The system must issue the Write-to-Buffer-Abort-Reset command sequence to return the EAC to standby
(read mode) and the Status Register failed bits are cleared. See
more details.
Notes:
1. DQ5 switches to '1' when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits. See
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details
3. Data are invalid for addresses in a Program Suspended Line.
4. DQ1 indicates the Write-to-Buffer ABORT status during Write-Buffer-Programming operations.
There are three types of errors reported by the embedded operation status methods. Depending on the error
type, the status reported and procedure for clearing the error status is different. Following is the clearing of
error status:
If an error occurs during an embedded operation (program, erase, blank check, or password unlock) the
device (EAC) remains busy. The RY/BY# output remains Low, data polling status continues to be overlaid on
all address locations, and the status register shows ready with valid status bits. The device remains busy until
the error status is detected by the host system status monitoring and the error status is cleared.
During embedded algorithm error status the Data Polling status will show the following:
Standard
Suspend
Suspend
Write-to-
Program
(Note 3)
(Note 4)
Buffer
Exceeded Timing Limits on page 43
Mode
Mode
Erase
Mode
If an ASO was entered before the error the device remains entered in the ASO awaiting ASO read or
a command write.
If an erase was suspended before the error the device returns to the erase suspended state awaiting
flash array read or a command write.
Otherwise, the device will be in standby state awaiting flash array read or a command write.
DQ7 is the inversion of the DQ7 bit in the last word loaded into the write buffer or last word of the
password in the case of the password unlock command. DQ7 = 0 for an erase or blank check failure
DQ6 continues to toggle
DQ5 = 1; Failure of the embedded operation
Embedded Program Algorithm
Reading within Erasing Sector
Reading Outside erasing Sector
Reading within Program Suspended Sector
Reading within Non-Program Suspended
Sector
Reading within Erase Suspended Sector
Reading within Non-Erase Suspend Sector
Programming within Non-Erase Suspended
Sector
BUSY State
Exceeded Timing Limits
ABORT State
Operation
D a t a
for more information.
S h e e t
GL-S MirrorBit
Table 5.5 Data Polling Status
( A d v a n c e
®
(Note 2)
INVALID
Allowed)
Family
DQ7#
DQ7#
DQ7#
DQ7#
DQ7#
DQ7
Data
Data
(Not
0
0
1
INVALID
Allowed)
Toggle
Toggle
Toggle
Toggle
Toggle
Toggle
Toggle
Toggle
Data
Data
DQ6
(Not
No
I n f o r m a t i o n )
Write Buffer Programming on page 28
S29GL_128S_01GS_00_01 February 11, 2011
INVALID
Allowed)
(Note 1)
DQ5
Data
Data
(Not
0
0
0
0
0
0
1
1
INVALID
Allowed)
Data
DQ3
Data
(Not
N/A
N/A
N/A
N/A
N/A
N/A
1
1
INVALID
Allowed)
(Note 2)
Toggle
Toggle
Toggle
Toggle
DQ2
Data
Data
(Not
N/A
N/A
N/A
N/A
No
No
(Note 4)
INVALID
Allowed)
DQ1
Data
Data
(Not
N/A
N/A
N/A
N/A
0
0
0
1
RY/BY#
DQ5:
for
0
0
0
1
1
1
1
0
0
0
0