PIC24FJ32GA002-I/SO Microchip Technology Inc., PIC24FJ32GA002-I/SO Datasheet - Page 100
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
PIC24FJ32GA002-I/SO
Manufacturer Part Number
PIC24FJ32GA002-I/SO
Description
MCU, 16-Bit, 28-Pin, 32KB Flash, 8KB RAM, 21 I/O, Nanowatt
Manufacturer
Microchip Technology Inc.
Datasheet
1.PIC24FJ32GA002-ISP.pdf
(256 pages)
Specifications of PIC24FJ32GA002-I/SO
A/d Inputs
10 Channel, 10-Bit
Comparators
2
Cpu Speed
16 MIPS
Eeprom Memory
0 Bytes
Input Output
21
Interface
I2C/SPI/UART
Memory Capacity
32 Kbytes
Memory Type
Flash
Number Of Bits
16
Number Of Inputs
21
Number Of Pins
28
Package Type
28-pin SOIC
Programmable Memory
32K Bytes
Ram Size
8K Bytes
Speed
32 MHz
Timers
5-16-bit
Voltage, Range
2-3.6 V
Voltage, Rating
2-3.6 V
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
- Current page: 100 of 256
- Download datasheet (4Mb)
PIC24FJ64GA004 FAMILY
9.1.1
In addition to the PORT, LAT and TRIS registers for
data control, each port pin can also be individually con-
figured for either digital or open-drain output. This is
controlled by the Open-Drain Control register, ODCx,
associated with each port. Setting any of the bits con-
figures the corresponding pin to act as an open-drain
output.
The open-drain feature allows the generation of
outputs higher than V
digital only pins by using external pull-up resistors. The
maximum open-drain voltage allowed is the same as
the maximum V
9.2
The use of the AD1PCFG and TRIS registers control
the operation of the A/D port pins. The port pins that are
desired as analog inputs must have their correspond-
ing TRIS bit set (input). If the TRIS bit is cleared
(output), the digital output level (V
converted.
When reading the PORT register, all pins configured as
analog input channels will read as cleared (a low level).
Pins configured as digital inputs will not convert an
analog input. Analog levels on any pin that is defined as
a digital input (including the ANx pins) may cause the
input buffer to consume current that exceeds the
device specifications.
9.2.1
One instruction cycle is required between a port
direction change or port write operation and a read
operation of the same port. Typically, this instruction
would be a NOP.
EXAMPLE 9-1:
DS39881B-page 98
MOV
MOV
NOP
BTSS
Configuring Analog Port Pins
0xFF00, W0
W0, TRISBB
PORTB, #13
OPEN-DRAIN CONFIGURATION
I/O PORT WRITE/READ TIMING
IH
specification.
PORT WRITE/READ EXAMPLE
DD
(e.g., 5V) on any desired
; Configure PORTB<15:8> as inputs
; and PORTB<7:0> as outputs
; Delay 1 cycle
; Next Instruction
OH
or V
OL
) will be
Preliminary
9.3
The input change notification function of the I/O ports
allows the PIC24FJ64GA004 family of devices to gen-
erate interrupt requests to the processor in response to
a change of state on selected input pins. This feature is
capable of detecting input change of states even in
Sleep mode, when the clocks are disabled. Depending
on the device pin count, there are up to 22 external sig-
nals (CN0 through CN21) that may be selected
(enabled) for generating an interrupt request on a
change of state.
There are four control registers associated with the CN
module. The CNEN1 and CNEN2 registers contain the
interrupt enable control bits for each of the CN input
pins. Setting any of these bits enables a CN interrupt
for the corresponding pins.
Each CN pin also has a weak pull-up connected to it.
The pull-ups act as a current source that is connected
to the pin, and eliminate the need for external resistors
when push button or keypad devices are connected.
The pull-ups are enabled separately using the CNPU1
and CNPU2 registers, which contain the control bits for
each of the CN pins. Setting any of the control bits
enables the weak pull-ups for the corresponding pins.
When the internal pull-up is selected, the pin uses
V
there is no external pull-up source when the internal
pull-ups are enabled, as the voltage difference can
cause a current path.
DDCORE
Note:
Input Change Notification
as the pull-up source voltage. Make sure that
Pull-ups on change notification pins
should always be disabled whenever the
port pin is configured as a digital output.
© 2007 Microchip Technology Inc.
Related parts for PIC24FJ32GA002-I/SO
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![TC1014-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1014-5.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.5VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.8VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-4.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1186-2.5VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1186-2.85VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet: