PIC24FJ128DA110-I/PT Microchip Technology Inc., PIC24FJ128DA110-I/PT Datasheet - Page 260

• Manufacturer Part Number: PIC24FJ128DA110-I/PT
• Description: 100 TQFP 12x12x1mm TRAY, 16-bit, 128KB Flash, 24K RAM, USB, Graphics
• Manufacturer: Microchip Technology Inc.

Specifications of PIC24FJ128DA110-I/PT

• A/d Inputs: 24 Channel, 10-bit
• Comparators: 3
• Cpu Speed: 16 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 84
• Interface: I2C/SPI/UART/USART/USB
• Memory Type: Flash
• Number Of Bits: 16
• Package Type: 100-pin TQFP
• Programmable Memory: 128K Bytes
• Ram Size: 24K Bytes
• Speed: 32 MHz
• Temperature Range: –40 to 85 °C
• Timers: 5-16-bit
• Voltage, Range: 2.2-3.6 V
• Lead Free Status / Rohs Status: RoHS Compliant part

PIC24FJ256DA210 FAMILY
REGISTER 18-8:
DS39969B-page 260
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
R-x, HSC
JSTATE
U-0
—
Unimplemented: Read as ‘0’
JSTATE: Live Differential Receiver J State Flag bit
1 = J state (differential ‘0’ in low speed, differential ‘1’ in full speed) is detected on the USB
0 = No J state is detected
SE0: Live Single-Ended Zero Flag bit
1 = Single-ended zero is active on the USB bus
0 = No single-ended zero is detected
TOKBUSY: Token Busy Status bit
1 = Token is being executed by the USB module in On-The-Go state
0 = No token is being executed
USBRST: Module Reset bit
1 = USB Reset has been generated; for software Reset, application must set this bit for 50 ms, then
0 = USB Reset is terminated
HOSTEN: Host Mode Enable bit
1 = USB host capability is enabled; pull-downs on D+ and D- are activated in hardware
0 = USB host capability is disabled
RESUME: Resume Signaling Enable bit
1 = Resume signaling is activated; software must set bit for 10 ms and then clear to enable remote
0 = Resume signaling is disabled
PPBRST: Ping-Pong Buffers Reset bit
1 = Reset all Ping-Pong Buffer Pointers to the even BD banks
0 = Ping-Pong Buffer Pointers are not reset
SOFEN: Start-Of-Frame Enable bit
1 = Start-Of-Frame token is sent every one 1 ms
0 = Start-Of-Frame token is disabled
R-x, HSC
SE0
clear it
wake-up
U-0
—
U1CON: USB CONTROL REGISTER (HOST MODE ONLY)
U = Unimplemented bit, read as ‘0’
W = Writable bit
‘1’ = Bit is set
TOKBUSY
R/W-0
U-0
—
USBRST
R/W-0
U-0
—
HSC = Hardware Settable/Clearable bit
‘0’ = Bit is cleared
HOSTEN
R/W-0
U-0
—
RESUME
R/W-0
U-0
—
 2010 Microchip Technology Inc.
x = Bit is unknown
PPBRST
R/W-0
U-0
—
SOFEN
R/W-0
U-0
—
bit 8
bit 0